Jump to content
SAU Community

Recommended Posts

Hi Peoples,

Have a set of 4 brand new Brembo 4 piston calipers that I am looking to part with.

They have only been trial fitted to a car before they guy changed his mind, so they have NO time on them at all.

They were meant to go on a Grand Am race car.

The attached PDF will give you all the technical info you will need to know.

$5000 plus shipping

I am located in Wollongong NSW.

post-94131-0-72090300-1366672263_thumb.jpg

post-94131-0-72364700-1366672286_thumb.jpg

post-94131-0-62517700-1366672295_thumb.jpg

post-94131-0-54143700-1366672303_thumb.jpg

XA6.H7_Brembo_Racing_Catalog_2009_copy.pdf

Any interest from anyone?

I know there's some high rollers on here.

Grab some high quality gear at a great price.

  • 2 weeks later...
  • 2 weeks later...

Yeah i know.

I havent even been low balled yet lol.

Must be because kids are at school.

That being said, these are still available which is hard to believe.

I know there are some circuit cars being built on here. Im surprised no one has asked about them.

  • 2 weeks later...
  • 2 weeks later...

Go on..... do it..... you know you wana lol.

You know these are the shiz when they use them on GrandAm race cars.

Plus they havent even been used yet.

Save yourself a few grand and the wait.

  • 3 weeks later...

I am really surprised given the amount of builds going on that no one has snapped these up.

  • 1 month later...
  • 1 month later...

If you want to go fast, then you will need to stop fast. These will do the job!!!

If I had the cash, they'd be on the way to my house.

Unfortunately I'm broke as f**k, and can only afford Wilwoods. :(

Judging by the amount of time that ive had a hold of these, you're not the only one lol.

  • 3 weeks later...
  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • @Haggerty you still haven't answered my question.  Many things you are saying do not make sense for someone who can tune, yet I would not expect someone who cannot tune to be playing with the things in the ECU that you are.  This process would be a lot quicker to figure out if we can remove user error from the equation. 
    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
×
×
  • Create New...