Jump to content
SAU Community

Just Bought A 32, Where Are Some Good But Reasonably Priced Workshops In The South East?


Recommended Posts

Just picked up a mates gtst for a pittance but it needs some serious attention mechanically

I used to take my GTR to RE customs but it looks like their phone is off, ill go by their after work to see if they're still open

Can someone recommend a good reliable but reasonably priced workshop in the south east i can get it towed to, cant trust the drive, rather spend on a tow than damage the hydraulic / power steering system and cooling system.

ive read on hear about sabbadin automotive being ok, would like other suggestions, will try speak to both these people after work today

thanks in advance

Rich

Edited by V-Spec

i live south east, i know chasers is good but ill go speak to OTR, Sabbadin and see what happened to RE customs

anyone know if RE is still around, all these shops are relatively close to each other

thanks for the quick replys and information!!

what shop would be the best to source second hand parts and install them?

I thought otr is a supplier?

Sabbadin is great!

Chasers would be my bet

They have a workshop...they do very cheap work. My turbo install was $280 including removal and replacement of broken exhaust manifold studs.

wait, birds, were you talking about Sabbadin or chasers or your original recommendation of OTR?

im a bit giddy about the car, i re-read the thread and i think you mean OTR

Thanks!

Edited by V-Spec

RE customs moved shop to a few factories down. my run-ins with them over the last 12 months have not been positive.

+1 for sabbadin, also Ace Dyno + workshop in clayton is round that area. Anthony is a good guy.

Was talking about OTR...nice and helpful guys. Sabbadin also do great work, I don't imagine them being as cheap as OTR though.

Brad from RE now works at RTR in Dandenong. I had them do a wheel bearing and a service and we had the Member Renewal / Dyno Day there. I'll be going back for sure.

Was talking about OTR...nice and helpful guys. Sabbadin also do great work, I don't imagine them being as cheap as OTR though.

yeh sabbadin arent the cheapest, but you definitely pay for a good job done. hes worked on all of my cars.

Ive taken birds advice and organized things with OTR Rich

nice! i never knew they did service work, definitely wouldve gone to them if I knew

Brad from RE now works at RTR in Dandenong. I had them do a wheel bearing and a service and we had the Member Renewal / Dyno Day there. I'll be going back for sure.

RTR is great, great mechanics there, but are a little expensive.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • 310mm rotors will be avilable from Australia, Japan, and probably a few other places. Nothing for the front can be put on the back.
    • The filter only filters down to a specific size. Add to that, the filter is AFTER the pump. So it means everything starts breaking your pump even if its being filtered out.
    • Just like in being 14mm too small (296mm) makes it not fit, being 14mm too big (324mm) it also won't fit. You want to find the correct rotor.
    • @GTSBoy Ok so that was the shops problem...they showed R33 rotors on R34 page and i did not know 296 do not fit(and are for R33) Yes i bought "kit" with rotors and pads. Pads are ok(i have GTT calipers front and rear). They have some 324mm but no 310mm. So i dont know if they would fit. I have 17inch LMGT4s So another question. Can i fit those in the rear or they are just "too" big for that?
    • I started removing the tank a while back with the intent to give it a proper clean. Got to a bolt that I couldn't undo completely due to a diff being in the way, so just said f**k it and siphoned the gluggy old fuel out and called it a day. Looking it the tank it looks less corroded than the one in the pics for that billet hanger from Frenchy's anyway. Isn't it the fuel filters job to worry about this stuff? I scraped off most the crusty shit of the hanger but will give it another go before reinstall coz maybe the fuel and return pipes are also full of gunk  
×
×
  • Create New...