Jump to content
SAU Community

Stagea C34 Lost Power -- Limp Mode?

Rotaron
 Share

Recommended Posts

Rotaron Contributor

Rotaron

Posted
Posted

Hi all

I have a issue with my stagea concerning the loss of power., possibly in some sort of LIMP mode?

Car: Stagea C34 1999 model RS4S manual

Mods: Standard turbo, Large front mount intercooler, 12 PSI boost, POD filter & NISTUNE ECU, CAT back 3inch exhaust.. nothing over the top. She is a good tow car !!

Scenario: Driving to work the other day gave the car a boot full to get around some cars, The car during hard acceleration had a massive hesitation ( similar to bouncing off rev limiter) then backfired. I lifted off quickly and then from then on the car has had no power or even very little boost.

It will very slowing accelerate to speed and you can here it labouring ( But not missing or poping or pinging).

Car idles nicely every thing works.. no engine light ... i am also able to rev the with no load and it will rev to 6k to 7k no problem.

No oil leaks,

No blue smoke out of the exhaust.

Engine is idling beautifully sits on 900 rpm rock solid.

everything under the bonnet looks ok.!!!! :wacko:

Things i have tried:

Did a full ECU check using the consult port and it gave me code 55 - meaning no problem found with ECU.

Disconnect battery for a couple of hrs then reconnected to no eval.

I checked all of the hose's including turbo piping to see if something is blown off.. nothing found

I checked Air flow meter for damage but nothing looks bad. I even disconnected the airflow while the motor was running and it started to hunt then die hence i am thinking air flow meter is OK.

What to try next?

Is there a possibility of a blown turbo?

Can there be a ignition issue?

Can there be other sensors but surely that would cause the ECU to give a problem code??

Co lapsed Cat?

Help would be appreciated!

Rotaron

Link to comment
https://www.sau.com.au/forums/topic/425361-stagea-c34-lost-power-limp-mode/
Share on other sites
Duncan Grand Master

Duncan

Posted
Posted

Well 9 times out of 10 those symptoms describe a pop-ed off or split intake pipe. The other time it is a blown turbo :( You really need to pull the dump pipe off to check the rear turbo wheel if you can't find a split hose, or maybe just check in the front of the cat....

Rotaron Contributor

Rotaron

Posted
  • Author
Posted

Can the AFM still be stuffed if it doesn't look physically damaged? And if it is stuffed then why does it idle so nicely? Surely the AFM would make it hunt or idle very poorly.

I also have new theroy:

Blown exhaust wheel off turbo shaft... hence no real boost? Looks like i will be taking off front part of exhaust to check for rear turbine has delaminated off the shaft. if it has it will be sitting next to the CAT. :woot:

Rotaron Contributor

Rotaron

Posted
  • Author
Posted

Hi lads

Confirmed it on the weekend when i pulled it out. Exhaust impeller blown to million pieces and wait for it .................. front compressor impeller blown in a million pieces as well :wacko: :wacko: :wacko: intercooler was full of broken bits. Cleaned everything out on the weekend with the hot high pressure spray hose at the servo.

Hence i just dropped the turbo off today to hypergear for high flow job. He is in Campbellfield.

Link here http://www.skylinesaustralia.com/forums/topic/261613-hypergear-hiflow-service-continued/

:yes: :yes: :yes: :yes:

Now i have ordered the new nissan tubo gaskits.

And i am after new fuel pump and injectors to suit the new turbo. Any suggestions... remember this is a street car.

Then off to get re-nistuned at the Dyno.

Not happy that it has happened but i am using this as a excuse to put some extra goodies into the car. Dont want to go stupid as it is still a daily driver / tow car for the race car.

Hence talking with the guy at Hypergear he advised that it will be nice and streetable with good low response but still have a good top end as well with his high flow job that he does. :rolleyes:

hoy32 Rising Star

hoy32

Posted
Posted

Walbro 255lph seems to be a straight forward install on the stagea. And seeings thought its your daily that will be enough for what you need.

http://www.skylinesaustralia.com/forums/topic/323722-stagea-walbro-pump-fitting-guide/

As for injectors Deatchwerks plug in with no mods, no rewiring needed. They are decently priced as well.

Rotaron Contributor

Rotaron

Posted
  • Author
Posted

New High flow turbo went in on the weekend.. All running well now. Have to baby it until i get the pump and injectors sorted out then get it Dyno tuned.

I gave it a light load squirt around the block with no issues's.

Certainly sounds different when it spools up...but turbo still seems nice and responsive... Time will tell when i get it all dyno'd :yes: :yes:

  • 4 weeks later...
picklesRs4 Community Regular

picklesRs4

Posted
Posted

sorry for starting up an old one again but i just want to ask when putting the highflow on did you have to get the tune and suppoting mods straiight away?

or can you just run it for as long as you want till you can afford supporting mods?

scotty nm35 Grand Master

scotty nm35

Posted
Posted

If you keep the boost low enough, like 7 psi, you should be able to drive it around ok, off boost should be fine. The ecu will definitely need a tune though, make sure you change the plugs for the tune as they will be fouled.

Sorry Rotaron, I should have mentioned I can help you out with prices on injectors and pump if needed, but I assume you are sorted by now...

Rotaron Contributor

Rotaron

Posted
  • Author
Posted

Well i be telling the truth when i say that i haven't had a chance to get it Dyno'd.... Just been to busy. racing my other car and plenty of work and home project on the go.

I have got the boost set at stock levels and it drives great.... Stagea towed my race car to the island no problem last weekend.

Also got my self some injectors and a new oxy sensor as well.

Still need to get the fuel pump as i havent had a chance to get that one sorted yet .

Then it is off to get it Dyno'd... hopefully in the next couple of weeks.

It all comes down to time. :wacko: :wacko: :wacko: :wacko:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Chupapy
      Coolant leak?

      By Chupapy · Posted

      Will have a look at that. I cant see any leaks 
    • GTSBoy
      Coolant leak?

      By GTSBoy · Posted

      Put another overflow bottle (ie, a 1.25 coke bottle or similar) under the overflow hose and see if it is being pushed out there or if it is disappearing into the engine.
    • GTSBoy
      New kid on the block

      By GTSBoy · Posted

      Staring on a stand is no issue. You just have to wire everything up, give it fuel and cross your fingers that the stand is robust enough. Arranging the inlet plumbing is often the hardest part, without any surrounding structure to hand some of it from. No need for coolant if you only want to run it for <1 minute. As to the gearbox - I think the little Aisin box is a bit stronger than the other small Nissan boxes that went behind SRs, but I wouldn't be too keen to test its limits with the torque of a boosted 25. I don't know if you can retain the box and the tailshaft. The box won't connect to the RB without an adapter of some sort, which is either a plate that will push the engine forward (which is not good for fitting it into the bay's available space) or push the box back, which messes with the box position and tailshaft length - OR - cut and shut work on the bellhousing, which is a long way from "least modification". I'd be buying a new 370Z 6 speed or similar, doing what has to be done to that to make it fit RB (ie, cut and shut bellhousing) and the requisite tailshaft custom/mods.
    • Songo
      New kid on the block

      By Songo · Posted

      Hi Everyone I am from West Pennant Hills in NSW. Been too busy until recently to attend to my RB25DET Series 2 engine until recently. I am planning to stick it into the S15 shell at this stage, unless a nice SR20DET turns up... For now, i am going to try and get the RB25 running and working well then decide what gearbox to use. My preference is to retain the SR20DET  6 speed gearbox and tail shaft to retain as much and least modifications as i can avoid. I am an old guy and won't be doing any heavy drifting so i don't need a bullet proof gearbox Does anyone have experience with starting the RB on a stand? I got everything setup as much as I can with the info i can find... endless searching and videos on Youtube I would be great to get some pointers Cheers Songo
    • Chupapy
      Coolant leak?

      By Chupapy · Posted

      Hey all, Recently have had my s1 r33 gtr serviced and noticed my coolant reservoir was topped up to the max line. Took the car out for 1 yesterday and noticed today the reservoir is completely empty.  Any ideas? Radiator is full
×
×
  • Create New...