Jump to content
SAU Community

Recommended Posts

Hey guys I have an R34 GTT coupe automatic. Was just wondering what you guys use/prefer as engine, power steering, transmission oils (brand/type) etc

I am curious as to what you guys think is best. The car goes through periods of everyday use and also theres times where it doesn't get driven for a week or so.

Also any other general tips for good maintenance (like letting the car warm up in the morning etc) would be great!

Thanks!

Josh

Link to comment
https://www.sau.com.au/forums/topic/426903-oil-types-maintenance/
Share on other sites

Personally I only use Royal Purple 10w40 engine oil, but that's just a personal thing. Lots of guys using Penrite, Motul, Gulf Western, etc. Weight of the oil you use depends on how many km's your engine has on it. Power steering I just use the OEM Nissan stuff, and I've got a manual gearbox so can't help you with transmission fluid.

As for maintenance, not a lot you need to do other than check fluid levels etc. every so while. The car should be fine sitting for a week or two, mine sits for months at a time haha. If it is going to be sitting for longer than two weeks without getting a decent drive, I recommend getting a 3-stage battery charger to ensure you get a good life out of your battery.

Don't let the car warm up in the morning by letting it idle, that's silly. It takes longer for the engine to warm up this way, and you need to warm up your gearbox and diff anyway. Plus you annoy your neighbors. Just drive the car gently for the first 10-15 minutes or so, depending on how cold it is. If you plan on doing some track work at any stage, some gauges (water/oil temp, oil pressure, etc.) wouldn't go astray and I find mine extremely useful. Otherwise, just drive the car like you would any other car, and service it regularly :thumbsup:

Edited by Hanaldo

Don't let the car warm up in the morning by letting it idle, that's silly. It takes longer for the engine to warm up this way, and you need to warm up your gearbox and diff anyway. Plus you annoy your neighbors.

+ your family, if your car is parked at the front of the house where the bedrooms are hahaha but i always find it amusing

  • 2 weeks later...

With warming up the engine. I would say to let it sit for a minute or two after startup so oil pressure builds, coolant can circulate, etc. Like not driving it immediately after the engine starts.

Oil I would say a decent 10W-40 is fine. Nothing super cheap, but you don't have to go super expensive either. Used Nulon Full Synthetic10W-40 previously and just put in Penrite 10 Tenths 10w-40, Penrite is not giving any lifter noise on startup whereas had some noise for a few seconds with the Nulon. Slightly thicker if the engine is older/using a lot of oil or used for track.

1 for Penrite

Warm up times is subject to much debate, lol.

As the guys have said, give it a minute or two to get some oil pressure, but also ease the box and diff in as well.

When I was daily-ing my Cefiro, I'd start the car, chuck my bag, phone, wallet etc on passenger seat, jump in, find some tunes/check Facebook, that'd kill about a minute or so, then roll it out the driveway, pop it into second and idle down my street (about 100-200 metres @ 20-30ish kmph??), then be gentle and stick below 2500rpm for the next couple of backstreets, then keep it under 4000rpm, then by the time I hit the highway it was up to temp.

Edited by Nic_A31

Mine takes ages to hit temp even while driving. Like i'm talking a good 15mins+. I think the thermostat may need replacing.

TBH, I usually warm the engine up to about 40-50 degrees with some throttle blips every couple mins before taking off. Take it easy, like no positive boost and <3000rpm, until oil pressure drops so i know oil is up to temp.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Lamb roast on Saturday will be different 🥲
    • They are under bucket shims. Tomei provides a test shim kit and then any measurement of shim required. 
    • I always wondered how you were supposed to buy a set of 24 buckets and somehow magically have every single one of them yield exactly the desired clearance. I would have thought you'd need to assemble a cam with either 12 "sample" or "example" buckets of known top thickness (or a single such sample/example 12 times over!!) measure clearances at every valve, and then do the usual math to work out what the actual "shimness" of each bucket needed to be, before buying the required buckets to make up he thicknesses that you didn't have on hand.
    • I now seem to be limited in power due to my rev limit/hydraulic lifters in my built RB25. I'm looking into converting over to Tomei solid lifters. Question for anyone that has done the conversion. I was always under the impression that when using the Tomei solid lifter conversion, you would also require new valves (Longer or shorter stems, I can't remember which).  I don't know where I got this idea, as so far I see no mention of this in any of the Tomei documentation. It just states I need the Tomei solid buckets, solid lifter cams and upgraded springs. As my head is already built, all I would need is another set of 1000$ Kelford cams, 500$ buckets and about 4H hours of my time installing and I'm off to the races!?!? There's no way it's that simple, I must be missing something? 
    • I couldn't agree more. I should have started from the get-go with a NEO or solid bucket conversion. I started looking into converting over to solid lifters yesterday. Now for some reason I was always under the impression that when using the Tomei solid lifter conversion, you would also require new valves (Longer or shorter stems, I can't remember which).  But I see no mention of this on any of the Tomei documentation. It just states that I need the Tomei solid buckets, solid lifter cams and upgraded springs. As my head is already built, all I would need is another set of 1000$ Kelford cams, 500$ buckets and about 4H hours of my time installing and I'm off to the races!?!? There's no way it's that simple, I must be missing something? 
×
×
  • Create New...