Jump to content
SAU Community

Recommended Posts

I have recently brought my first skyline and need to replace the rear tyres.

I have an r33 GTR VSpec with r34 gtr rims ( I think they are 18 x 9 ),

currently running 245 40 yokohama S Drives all round.

would it be a bad combination to put 275 40 KU19 on the back?

I was going to replace them with the same ones but the kumhos are on special for 200 each

Great site by the way

Link to comment
https://www.sau.com.au/forums/topic/426924-would-this-tyre-combination-work/
Share on other sites

A handy tool to use is this -

http://www.1010tires.com/Tools/Tire-Size-Calculator

It will show you what it does to the rolling diameter etc

thanks mate the tyre shop said it would work but i guess there were just trying to get rid of stock.

245 40 = 653mm

275 40 = 677mm

will it be a big let down if I replace the rear with the same tyres when the fronts have 60-70% tread.

The only 275 wide tyre that would (should) work would be a 35 profile. That is only 0.5% different to the front tyres you have.

In your situation I would do exactly what I do in my own situation. Run the same size tyres all around, replace one pair at a time. New ones go on the front, front ones go to the back. That way you always have the newest best tyres at the most important end, and there's never more than about 50% tyre wear difference between front and back.

Granted, on a GTR you really need to keep the tyres as close to the same size as humanly possible, but ~50% wear difference on the same size tyre shouldn't upset the ATTESSA too much.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...