Jump to content
SAU Community

Recommended Posts

Be careful going higher because if you go too high the stock shock will be at its full length of travel and won't work at all, it will bounce everywhere. My friend and I tried it on a commy ute and the rear lifted off the ground when braking hard

Well now they're getting cheaper at the bottom end, I think a grubby C34 would make a great softroader, basically.
Some slightly larger diameter all-terrain tyres (235/60R16 looks good and fairly common) would get a little clearance but at the same time would need a little more height to help guard clearance. I was thinking along the lines of stiffer springs and some strut top spacers.

I actually had a think about this as an option for a touring wagon/beach buss/camping wagon.

My stag is reasonably low. Honestly I don't have too many issues with driveways, speed humps or parking bollards (my front lip will clear a standard height concrete parking bollard by 2-3mm). We started taking it camping and day trips.... perfect for a blast up the east coast (Tassie) then cruise into a camping spot, most of the camping places are down dirt roads, on sand and washed out potholes. I'm surprised were I was able to take it..... the center diff lock and snow mode is great in rolled gravel or sand, just as long as you straddle the rutts :yes: . A couple of times I could actually go places the big 4WD guys couldn't go :woot: under fallen trees etc.

We ended up buying the missus an xtrail, suits her gutter riding duties better ( :no: my poor volk GTC's).

Long story short:

I was going to space up the sub-frames and between the shock and shock tower. Throw on some more off roadish taller tyres. Then use some aftermarket arms with slighlty longer stroke shocks/springs.

J

Hmm, I have some spare front shock absorbers for the stagea lying around. Theyre stagea specific ones and theyre slightly longer than GTR shocks. Longer stroke to the piston.

I guess theyre for what youre talking about. Most stageas are/were family wagons and snow cars, not sports cars.

Your biggest issues will be keeping the correct geometry if you change the relationship of factory pickup points/shock-spring length. The rebound geometry past horizontal gets squew wiff pretty quick.

If you space the sub-frames the same amount as the shock spacers, it keeps everything relatively sock for geometry/bump-steer etc If effect a 'body' lift.

XRATED, thats the same kind of thing that got me thinking, I've crawled into a few places it by all rights shouldn't have been, it seems very competent getting around on gravel and sand, through muddy paddocks and up and over stuff.

I think the rear subframe could be spaced down, isn't the upper arm in the front mounted to the chassis though? so I'm guessing that wouldn't work for the front. Ours seems to have a little negative camber on the back at stock height so I'm guessing a little bit of lift via spring/strut there wouldn't hurt, front I'm not so sure how much you could lift without going into positive camber.

Clearance wise I think with early bumpers, no skirts and no lips it wouldn't be too bad, sump does hang pretty low but could always run a bashguard tied back to the crossmember.

Edited by floody

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Update: tested my spark plugs that are supposed to be 5ohms with a 10% deviation and one gave me a 0 ohms reading and the rest were 3.9ohm<, so one bad and the others on their way out.
    • 9" wheels are a little too wide for a RWD 32. They can fit. People have put R33 GTR wheels on 32s for years and years. But they are a very tight squeeze. This has been known for about 30 years. As I said - there is no difference between a 17 and an 18 in terms of what will fit. The rolling diameter needs to stay about the same as stock - not very much larger. If you increase that, you will start to have problems. If you increae rolling diamater at the same time as yo increase width, you will have problems earlier. as 9" wheels are pushing the boundaries already, you would need to be careful with tyre choice. I would put 8.5s on the front of mine, but would expect problems with 9s.
    • post up screen shots of your injector tables
    • Diagnostic flow for a code 21 says check signal at the ECU pins, on a voltmeter of some kind it should read 0.1V at idle, 0.12V cranking, 0.15-0.25V at 2000 rpm. Check each coil such that +1, -3 is infinite or very high resistance, -3, +2 should do the same. (-1, +3), (+3, -2), (+1, -2), and (-1, +2) should all be somewhere between 0 ohms and high resistance. If you trace the path from the coil pin all the way back to the ECU in the diagram the resistance you measure at the coil vs connected to the harness should be pretty much the same. 
    • I have an elite 2500 running an adapter harness on an rb25de neo r34. I took the butterfly out and removed all that junk. But I also went Plus+t at the same time. The butterfly thing works in reverse to the boost solenoid on the Gtt if that makes sense
×
×
  • Create New...