Jump to content
SAU Community

Recommended Posts

Be careful going higher because if you go too high the stock shock will be at its full length of travel and won't work at all, it will bounce everywhere. My friend and I tried it on a commy ute and the rear lifted off the ground when braking hard

Well now they're getting cheaper at the bottom end, I think a grubby C34 would make a great softroader, basically.
Some slightly larger diameter all-terrain tyres (235/60R16 looks good and fairly common) would get a little clearance but at the same time would need a little more height to help guard clearance. I was thinking along the lines of stiffer springs and some strut top spacers.

I actually had a think about this as an option for a touring wagon/beach buss/camping wagon.

My stag is reasonably low. Honestly I don't have too many issues with driveways, speed humps or parking bollards (my front lip will clear a standard height concrete parking bollard by 2-3mm). We started taking it camping and day trips.... perfect for a blast up the east coast (Tassie) then cruise into a camping spot, most of the camping places are down dirt roads, on sand and washed out potholes. I'm surprised were I was able to take it..... the center diff lock and snow mode is great in rolled gravel or sand, just as long as you straddle the rutts :yes: . A couple of times I could actually go places the big 4WD guys couldn't go :woot: under fallen trees etc.

We ended up buying the missus an xtrail, suits her gutter riding duties better ( :no: my poor volk GTC's).

Long story short:

I was going to space up the sub-frames and between the shock and shock tower. Throw on some more off roadish taller tyres. Then use some aftermarket arms with slighlty longer stroke shocks/springs.

J

Hmm, I have some spare front shock absorbers for the stagea lying around. Theyre stagea specific ones and theyre slightly longer than GTR shocks. Longer stroke to the piston.

I guess theyre for what youre talking about. Most stageas are/were family wagons and snow cars, not sports cars.

Your biggest issues will be keeping the correct geometry if you change the relationship of factory pickup points/shock-spring length. The rebound geometry past horizontal gets squew wiff pretty quick.

If you space the sub-frames the same amount as the shock spacers, it keeps everything relatively sock for geometry/bump-steer etc If effect a 'body' lift.

XRATED, thats the same kind of thing that got me thinking, I've crawled into a few places it by all rights shouldn't have been, it seems very competent getting around on gravel and sand, through muddy paddocks and up and over stuff.

I think the rear subframe could be spaced down, isn't the upper arm in the front mounted to the chassis though? so I'm guessing that wouldn't work for the front. Ours seems to have a little negative camber on the back at stock height so I'm guessing a little bit of lift via spring/strut there wouldn't hurt, front I'm not so sure how much you could lift without going into positive camber.

Clearance wise I think with early bumpers, no skirts and no lips it wouldn't be too bad, sump does hang pretty low but could always run a bashguard tied back to the crossmember.

Edited by floody

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • sold listed as a Tomei LSD 1.5 Way For 1998+ Nissan Skyline ER34 25GT RB25DE w/Open R200 https://www.ebay.com/itm/174006114594?campid=5338967980&mkevt=1&mkcid=1&toolid=10050&customid=&mkrid=711-53200-19255-0&loc_physical_ms=108689&loc_interest_ms=&campid=5338967980&mkevt=1&mkcid=1&toolid=10050&customid=71883f2ccc571356e0a757bc7adfdde2&mkrid=710-53481-19255-0&loc_physical_ms=108689&loc_interest_ms= it went in like butter all gears, alignment, back lash etc, rotation and clearances correct, and if rolling all rotates smooth and free when coasting down road , clutch in or out over 10 mph smooth... its the binding, clunking and jerking from a stop that is most concerning, also seems like its going to tear the tires off in 10 miles of normal road driving. 
    • What 1.5 way? There's no such thing really as a 1.5 way, just different ways of explaining 2 ways with different ramp rates. HOWEVER. In any driving in a straight line your 1.5 or 2 or 1.7 way should have no clunking at all. With the clutch fully depressed the diff should be silent (unless it's welded but I'm assuming it's not). Something aint right here.
    • Clutch is a spec brand, new clutch system,( PP, flywheel, friction disc, etc. pull type) installed 100 miles ago, with no problems.
    • looking for some help and maybe some insight on others experience with a new LSD. R34 GT ran and drove beautifully, but always alot of grip loss due to the open R200 rear end, so I just installed a new 1.5 LSD way into the stock open R200 for a ER34. Simple. Everything seemed right. I test drove for the first time this weekend. as I started to back out the garage the first time slowly with tires straight it sounded and felt like I had a loose or half disconnected drive shaft...that was clucking around loose and shaking entire vehicle, and making it feel like the trans clutch was spontaneously slipping then grabbing very roughly while just letting out pedal slowly. I backed it out went to pull forward with the same noise, shake and slip grab feeling with hesitation, I turned the tires to back out more and then pulled ahead some same thing but worst because of added wheel resistance (which that I expected) puzzled … pulling it back in checking everything over and finding nothing wrong, I tried it the next day. same thing, couldn’t believe how it shook everything again making a terrible noise and making it feel like the trans clutch was slipping and grabbing, but I got it out of garage into the driveway, got it straight, drove forward and then reveres a few times in a straight line everything shaking , causing what felt like clutch slip and grab every time, sounded like right behind front driver tire and I could feel it in the floor board with my feet,... worst right when beginning to let clutch pedal out to engage slightly, shuttering and sounding terrible along the way…I managed to slowly get down the road, babying it the whole way, once I was rolling (out of 1st) seemed to be better and between shifts, then clutch felt closer to normal…not slip/ grab etc., but back down to any stop, straight road or turning, same thing. Made no difference if all tires were straight or if I was turning. All other gauge read out correct. with in 2 miles as planned I reached the empty parking lot and performed the break in procedure that came with lsd, essentially to drive in a figure 8 a bunch.  Did this, binding chattering, and shaking the car the whole way. I drove it back home seemed somewhat normal once I was in straight line and past 10 mph or so, and I know it will “bind” on corners and cause some tires squeal when turning especially from a stop, but when I begin to move it still causes what feels like the trans clutch to slip and jerk badly as well as shaking the entire car, and sounds terrible, that I didn’t expect. I used the fluid they supplied with LSD kit and did the breaking, planning to change fluid as they suggest after breaking, but wondering will it get smoother or less aggressive with use? maybe a 1.5 is just too aggressive for normal road driving?   I have a LSD that I put in my 71 cuda when I restored it, with amazing smooth , quite yet effective results. Different style LSD but that ones a joy to drive. maybe expecting too much from this R200?
    • Join SAU NSW for a flame-grilled feed & flame-spitting cruise! Sunday 17th August 2025 3:30PM Meeting Archies Flame Grille Sylvania Waters 4:45PM Cruise Departure 5:15PM Arrival at Cape Solander Kurnell Meet Location: Archies Flame Grille Final Destination: Cape Solander Kurnell *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
×
×
  • Create New...