Jump to content
SAU Community

Recommended Posts

Anything I should know about doing this? Take off the wipers and then under the screws? The screws are a funny profile on the head, sorta square shaped. Are they screws or a type of automotive fixing? Just unscrew them? Just don't want to get half way through and find it's harder than it looks......

Thanks guys.

post-46395-0-38904900-1371875549_thumb.jpg

It's very easy.

Your on the right track. Remove the wiper arms first.

With the clips they're automotive fixings. Be careful when removing.

If I remember correctly it's a half turn and lift.

Remove the rubber strip at the base. There will be "T" pieces holding it on. Just stretch one way and lift off.

It's likely going to be gungy under there . Mine was dried up mould but cleaned up easy and looks great.

Ps. If you happen to loose or break one of the fixings O'briens will have some :)

Mine were easy and never looked like breaking.

When Obriens came around to put my new OEM windscreen in he was surprised that I hadn't broken or lossed any.

That's why I mentioned being careful

Any dramas leaving the plastic panel off for a while whilst exposed the rain? I note that there is a large opening under the grilled section and I'm unsure where this goes to. I presume it drains as normally water would go through the grill and into it?

After. Some surface rust which I'm wondering how to deal with. I guess to do it properly I'll have to mask, sand, and use some sort of rust inhibiting primer (which hopefully will roughly match the grey). Bottom winscreen wiper nuts are corroded so I'll loosen them and try and make sure they no not sieze and the bolt thread is still OK.

So, under that plastic panel lurks all sorts of mud and dirst and grime which idealy would get cleaned out every couple of years. Another area I've noted that traps a lot of grime is behind the tail lights. I'll get onto this fairly soon as it looks filthy in there.

I've actually covered the car with a cover whilst the plastic panel is off as I think water will get into the engine bay without it.

post-46395-0-26563100-1371968281_thumb.jpg

post-46395-0-15753000-1371968290_thumb.jpg

post-46395-0-61698400-1371968298_thumb.jpg

post-46395-0-72897700-1371968305_thumb.jpg

post-46395-0-42825300-1371968313_thumb.jpg

  • Like 1

Oh yeah, the rubber strip does need to come out and I found the only way to do this was to use a flat screw driver blade and carefully pry out the fixings. By the look of them they just press back in so I think this is actually the way to remove them rather than just my hamfisted ways. They are actualy integral to the strip so you can't actually get to them as they are housed within it. Anyhow hope this is helpful to other in the future.

So.......the Autobarn guy didn't really inspire me with a lot of confidence with his advice so I thought I'd come here. The question I have is how I deal with the rust. Most of it is surface but there is one small spot (say 5mm diameter) which looks a little more serious. I'm thinking I sand back the surface rust, dig out the 5mm spot, and then spray with.....?

Clearly the black cover will hide any paint I put on there but I'd prefer to keep it looking as factory as possible so can anyone recommend a product that will match the underbonet colour for a silver GTR and that will be appropriate for addressing the rust as described. I think there are paint products that actually turn rust into something benign, but are they only available in black?

Thanks.

I think there are paint products that actually turn rust into something benign, but are they only available in black?

Thanks.

fill and paint over? also, no idea what product this is but just an idea, even if this product is black then you can just paint over it again...right?

Kill rust is a clear solution you could try

http://www.wattyl.com.au/en/find-the-right-product/exterior/Metal/Prepare/WattylKillrustRustEeter.html?preview=true

Supercheap sells white kill rust epoxy enamel

Edited by BstewyR33
  • 2 weeks later...

Went the easy / smart solution and took it to Micolour to get it sorted properly. Had some other minor blenishes attended to whilst I was there and also got the front guards spaced out for tyre clearance without losing my guard liners.

Looks too good to put the gutter back on!

I get it back today and will get her cut and polished next week after the rear diff rebuild.....Look out bank account.

post-46395-0-93010600-1373061564_thumb.jpg

post-46395-0-17581900-1373061573_thumb.jpg

post-46395-0-45627700-1373061582_thumb.jpg

post-46395-0-23689900-1373061590_thumb.jpg

post-46395-0-98043700-1373061598_thumb.jpg

post-46395-0-72461500-1373061606_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
×
×
  • Create New...