Jump to content
SAU Community

Recommended Posts

I have a very rare new Nismo Air Inlet pipe kit to fit R34 and R33 GTR the kit was only used as a display was never fitted to a car this kit is slightly different to the normal kits nismo sell as this kit seemed to be only produced around 2001-2002 when the prototype nismo Z-tune Z1 and Z-tune ver.2002 were being built as it was used on these cars.

Iam looking for $1400 includes delivery the normal nismo kits sell for min 135,000yen with the current rate you would be looking at around $1550 plus postage and import duties and with the amount of work gone into these kits they are worth more then the normal nismo kits being sold today

post-277-0-89595200-1372643228_thumb.jpgThe top pipe is the pipe for sale the bottom is the normal pipe nismo sell

post-277-0-47772400-1372643421_thumb.jpg This pic shows what the normal nismo inlet pipe looks like inside were the two pipes merge

post-277-0-53935700-1372643524_thumb.jpgThis pic shows the pipe for sale alot more work has gone into this pipe everything has been smoothed over and knife-edged

post-277-0-42640700-1372643947_thumb.jpgAnother pic showing the difference of the two pipes one on the left is the normal nismo pipe with the lip on the internal side of the pipe the right nismo pipe it is completely smooth it is like this on all the ends of each pipe in the kit

post-277-0-57418200-1372644351_thumb.jpgThis is the complete kit that is for sale

  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
×
×
  • Create New...