Jump to content
SAU Community

Recommended Posts

hey guys got a r32 gtst. 1993 model second owner in aus

car has alot of good parts on it.

rb20 stock with 130 thousand ks on it healthy strong motor with gearbox computer turbo loom and a twin plate clutch worth $$$ after 1500 for it all.

gtr genuine bonnet 500$

Gtr genuine grill 150$

Gtr fiberglass bar 300$

Gtr boot and spolier 250$

coil-overs 400 think there Hks there purple?

Nismo cat back exhaust 400$

inter-cooler kit not sure what brand 300$

carbon fibar front guards 150$ each ( wider then gtr )

doors 170$ each

cradle with lsd diff 400$

rear bar 100$

and what ever else you need tex me and ill give you a price.

located in melbourne 0401 906 086

post-58084-0-35136500-1373794121_thumb.jpg

post-58084-0-00313500-1373794153_thumb.jpg

post-58084-0-65557400-1373794163_thumb.jpg

post-58084-0-97929400-1373794341_thumb.jpg

front guard, coilovers, front grill, rear boot and spolier, rear bar , center dash , glove box, tail shaft, indicators ALL SOLD !!!!!!!!!!! still got motor, box, gtr bonnet, gtr front bar, nismo exhaust cat back, full intercooler, doors, front lights, seats, and most of the interior.

IF SOME 1 HAS A DAMAGED R32 AND NEEDS A CUT WILL SELL WHAT YOU NEED :)

still got a fair bit interior left !!!! also got a rb20 with 130ks very healthy with 5speed gearbox and twin plate clutch comes with computer wiring and turbo FULL COMPLETE RUNNING GEAR 1450

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • UPDATE: Yes the GSP Axles are compatible. I installed it on my R34 today and they are working a treat! Turns out that the S13, S14, S15, and 200 SX all used the same axles as the HR34, and ER34 NA models. Which is 2 bolt x 3 pairs.  
    • Also build this EH ute with 370z motor and gearbox with a couple of turbos just for fun.  
    • Got the passenger door on plus the master cylinder and booster. Loaded up to take it home. At home, the colour changes a lot in the light.
    • Nothing cheap, but I have seen the AC Hydraulic DK13HLQ which is pretty close to what you're asking for. The problem is the hydraulic cylinder mandates that the back of the jack be a certain height and Skylines have fairly deep inset floor jack points. A more certain and cheap option is to get some nominal 2x10 inch lumber boards and have one board be 1.5 feet, the other board 3 feet. Glue it all together with lots of clamps to maintain pressure. Make two of these. The ramp suggested above is a good idea, it takes quite a bit of clutch slip to get over each of the boards. I only need the first ~1.5 inches for my low profile jack on a standard ride height car but a lowered car you want to go up to the full ~3-3.5 inches. Paint it or store indoors if you want it to last.
    • Ok. And Nistune? I read (here too) mainly on Stagea threads that it can by "turn off" with Nistune. But they say they still had the sensor plug in. Next week iam going to the Nistune(and other ECUs) tuner so i can finally make it work. I drove the car home and apart from the cut it drove great. No misfire no smoke no hesitation or rough start...so hoping it is this sensor that is missing  
×
×
  • Create New...