Jump to content
SAU Community

Recommended Posts

Just got back from Wakefield. R888 can choke on a big dick. Mine were old, so they took a while to get some heat in and come back to life, but I got juddering understeer, the got hot, and then wouldn't turn. I had nt01 on the rear which was better, as newer, but found they went off after 5 or 6 laps. May need to decrease pressure more.

End of the day, the semis were no faster than my federal RSR time.

Interesting!!

Might add, I can't drive for shit, and I pussehed out under brakes lots.

Also, semis are a lot more communicative v rsr, and I found myself catching oversteer better.

Well i will be in the same situation! Will try do a run on RSR too see how i handle that first ;)

Is anyone out there running the same comp tyre for sprints and hill climbs and if so are you just starting the pressures higher for hill climbs???

Yep. I used to run A032R and Toyo RA1 back when I was hillclimbing and sprinting. For hillclimbs you basically want to start with cold pressures set to what the tyre's hot pressure should be at sprints - depending on how much of a burnout you do, you might start the rears a pound or two lower.

Just got back from Wakefield. R888 can choke on a big dick. Mine were old, so they took a while to get some heat in and come back to life, but I got juddering understeer, the got hot, and then wouldn't turn. I had nt01 on the rear which was better, as newer, but found they went off after 5 or 6 laps. May need to decrease pressure more.

End of the day, the semis were no faster than my federal RSR time.

old semis on the front and newer ones on the back was never going to be a recipe for success. Particularly in winter at Goulburn. Not really fair to compare them to a matched set of RSRs all round.

I was pretty critical of R888s when i had them, because they didn't seem to offer much grip. But they can produce good lap times if you are prepared to throw the car around. I was only a tenth faster at Lakeside when i changed to FZ201s. But the car felt much more planted on the Federals, and needed less steering angle almost everywhere.

People say the R888 seem to work well on light cars. I think its more that the really light cars tend to be less powerful. R888s don't like putting power down while exiting corners in my experience. A lighter less powerful car wouldn't really test them so much in that regard.

Edited by hrd-hr30

old semis on the front and newer ones on the back was never going to be a recipe for success. Particularly in winter at Goulburn. Not really fair to compare them to a matched set of RSRs all round

Yup, agree with you, when I cleaned them up this morning for storage, I also found the front left, the one I was having trouble with is 6 years old. Lol.

I'll try some re55s on the front next track day.

Wakefield wasn't actually cold yesterday, it was quite warm.

Yep. I used to run A032R and Toyo RA1 back when I was hillclimbing and sprinting. For hillclimbs you basically want to start with cold pressures set to what the tyre's hot pressure should be at sprints - depending on how much of a burnout you do, you might start the rears a pound or two lower.

.

cool, thought that might be the case. Still bummed about the federals, have searched around and found a few other sites where people have found a difference in the new FZ 201's. at 365 per corner they would of been very affordable. That's life I guess. Kumho's still the hot favourite I think ATM, performance-dollar-life wise. Not much cheaper than z221's but life span is sounding better still.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...