Jump to content
SAU Community

Recommended Posts

Hey all,

Need to clear out some room from the shed and need these parts gone as I no longer need them. All parts were removed in working order and were replaced only by new parts for the new set up of the cars. The list is below and will add photos later but you can PM me on here or sms me on 0400262578 for pics. Will try to upload pics as soon as possible.

33 GTSt Stuff

1. rear stock lower control arms $80 the pair

2. rear stock camber arms $40 the pair

3. rear stock traction rods $40 the pair

4. HICAS 4 wheel steering unit + tie rods $100

5. complete front and rear calipers and rotors only (no hubs or knuckles) $300

6. Diff centre minus ring gear $200

7. a/c condenser unit and all under bonnet lines to firewall $100

8. washer bottle and both motors $30

9. TRUST pod filter with green label air flow meter $80

10. clutchless fan $30

11. BLITZ blow off valve (rare) $100

12. turbo induction piping $10 each

13. fuel tank and fuel pump assay $150

14. cat back exhaust and kakimoto cannon (mild steel) $100

15. front castor rods $100 the pair

16. front LCA's $100 the pair

17. front camber arms $40 the pair

18. front traction rods $40 the pair

19. RB25 gears set and selectors + main shafts $400

20. generic 12' thermo fan $80

33 GTR stuff

1. crank scraper (2 piece) $40

2. rear main crank seal $20

3. power steering pump bracket $20

4. stock water pump (no cavitation) $30

5. exhaust manifolds with heat shields $40 the pair

6. oil and water turbo lines $5 each

7. various water and vac lines $5-$15

8. air ballast chamber $30

9. O2 sensors $5 each

10. stock valve springs and retainers $100

Any more stuff I find in my travels I will add at a later date!

Cheers HULI

also have an air regulator for RB26

(the bit that sits under the intake plenum)

Also have the centre grille for a S1 GTSt

(mint condition and in 2PAK silver)

7. a/c condenser unit and all under bonnet lines to firewall $100


8. washer bottle and both motors $30



how much to post this to canberra? does the air con stuff come with the compressor?

For all those people asking the front rotors measure 29.5mm in width and the rears measure 19mm in width. these come with the front and rear disk callipers and brake pads. so slap it on and go!!!!

Still got the O2 sensors and in very good condition!

If anyone needs better photos or something let me know and I can put them up on here or msg me and I'll send you a MMS. My number is 0400262578

Cheers HULI

PS would rather have pick up for exhaust system.

Also if you need some parts and not others I am willing to separate if need be!

If you want quality used stock parts and don't like the price, then shoot me a pm or msg with your offer and we'll go from there. All postage paid by buyer tho!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So, version 4 intake is on its way I was looking at these a while ago but at around $200 or more it was a little pricey for something that might not work, but, I had it in my watch list, but, I got a message saying it was on special, and I had a code thingie to use, it eventually came in at $120 delivered, so BAM, BUY NOW.....LOL I'll need to have a look when it arrives but I feel it will "look" better than what I currently have, as it comes with a PCV fitting, so I will be able to get rid of the alloy pipe that goes to the throttle body with the PCV fitting  Well, that's what the voices in my head are telling me  Oh, and this happened today Yeap, it was a Trojan, and it was cheap, so I headed back to the hardware store and actually spent a little bit more on a heavy duty,  one that was actually recommended by a plumber mate, a Cyclone one with a fibreglass handle that is actually rated for clay The broken shovel will eventually be "modified" into a short handle shovel
    • When you pulled it off, there is no signs of blown head gasket? Is it possible you have some other issues going on? Possible cracked blocked? Or do you think it's straight up lifting the head? Did you check what the head was torqued to before pulling it down (To see if possibly they're stretching, or starting to break threads out etc)?
    • Seems like a decent result for a modded JZX110. They are bulky in comparison to the 100 and 90 models (which I'd prefer myself) but they are getting very few and far between here in JP these days. Thanks for the detailed review and the import process into the UK. I also have a car which I'm hoping to export from Japan at some stage so it's good to know if someone from the UK was interested in it. By the way the corrosion underneath is par for the course for cars which were located in/near the mountains or along the Japan sea coastline. They get huge amounts of snow every winter and the sodium chloride is used on the roads. Many cars have some kind of rubber like treatment underneath but they tend to limit it to the wheel arches underbody and fuel tank. Suspension arms and sub-frames will have similar corrosion to your JZX110 which is a common sight. See it all the time and car dealers here generally don't even mention it unless asked.
    • If the sound goes away when you clutch in, the 1.5/2 way diffs are just shit, and you are a normal person. The diff is likely "fine" but driving at anything under 30kmh is a violent horrible experience. It would be exaggerated with solid diff bushings and subframe bushings if you have those.
×
×
  • Create New...