Jump to content
SAU Community

Recommended Posts

Friday, sounds good.

Got a hole in my front right tyre, its not all the way through, but it is into the belt.

Been doing some research, and there is a good method of repairing from inside the tyre. However it may not be good enough for Wakefield.

This:

A punctured speed rated tire brings with it additional considerations. While some tire manufacturers "allow" a tire to retain its speed rating if a specified multi-step repair procedure is followed exactly, most tire manufacturers reason that since they have no control over the damage caused by the puncture or the quality of the repair, they cannot confirm that the tire has retained its high speed capability. Therefore, their policy is that a punctured and repaired tire no longer retains its speed rating and should be treated as a non-speed rated tire.

Fresh brake pads and fluid going in this time.

And ill bring PLENTY of top up fluids too, its not hillclimbing.

Diff isnt leaking too bad, i will fix it before then if i can get a seal easy. Otherwise i can top it up if it needs it.

  • Like 1

Friday, sounds good.

Got a hole in my front right tyre, its not all the way through, but it is into the belt.

Been doing some research, and there is a good method of repairing from inside the tyre. However it may not be good enough for Wakefield.

This:

A punctured speed rated tire brings with it additional considerations. While some tire manufacturers "allow" a tire to retain its speed rating if a specified multi-step repair procedure is followed exactly, most tire manufacturers reason that since they have no control over the damage caused by the puncture or the quality of the repair, they cannot confirm that the tire has retained its high speed capability. Therefore, their policy is that a punctured and repaired tire no longer retains its speed rating and should be treated as a non-speed rated tire.

It'll be fine. Repaired a few of them with rubber inserts . It is really difficult to tear the belts on a tire. I'm pretty sure manufacturers err on the side of caution.

Fresh brake pads and fluid going in this time.

And ill bring PLENTY of top up fluids too, its not hillclimbing.

Diff isnt leaking too bad, i will fix it before then if i can get a seal easy. Otherwise i can top it up if it needs it.

Very good idea to bring top up fluids!

I have Project Mu mixed street/track brake pads and they hold up well, especially with the slotted rotors up front - still usable on the street too.

Make sure you also bring a bit of extra oil, as consumption increases a lot with a hot turbo on track (in my experience)

Brake bleed before and after will also make a big difference.

Also take a jerry can of fuel or two

  • Like 1

Tyre pressure makes a big difference.

Theres a big air compressor at the track, at the end of the sheds.

Im getting a good gauge, had to wait, hopefully they have stock now.

Also i have that temp gun, to see what temps were getting on the tyres.

Well unfortunately my leave wasn't approved.. Going to be too hard at the moment at work.. :(

I'll have to look into going another day some time in the future I suppose

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I feel I should re-iterate. The above picture is the only option available in the software and the blurb from HP Tuners I quoted earlier is the only way to add data to it and that's the description they offer as to how to figure it out. The only fields available is the blank box after (Input/ ) and the box right before = Output. Those are the only numbers that can be entered.
    • No, your formula is arse backwards. Mine is totally different to yours, and is the one I said was bang on at 50 and 150. I'll put your data into Excel (actually it already is, chart it and fit a linear fit to it, aiming to make it evenly wrong across the whole span. But not now. Other things to do first.
    • God damnit. The only option I actually have in the software is the one that is screenshotted. I am glad that I at least got it right... for those two points. Would it actually change anything if I chose/used 80C and 120C as the two points instead? My brain wants to imagine the formula put into HPtuners would be the same equation, otherwise none of this makes sense to me, unless: 1) The formula you put into VCM Scanner/HPTuners is always linear 2) The two points/input pairs are only arbitrary to choose (as the documentation implies) IF the actual scaling of the sensor is linear. then 3) If the scaling is not linear, the two points you choose matter a great deal, because the formula will draw a line between those two points only.
    • Nah, that is hella wrong. If I do a simple linear between 150°C (0.407v) and 50°C (2.98v) I get the formula Temperature = -38.8651*voltage + 165.8181 It is perfectly correct at 50 and 150, but it is as much as 20° out in the region of 110°C, because the actual data is significantly non-linear there. It is no more than 4° out down at the lowest temperatures, but is is seriously shit almost everywhere. I cannot believe that the instruction is to do a 2 point linear fit. I would say the method I used previously would have to be better.
×
×
  • Create New...