Jump to content
SAU Community

Recommended Posts

Hey ya'll, I've got a series 2 R33 Skyline Gts-t here in Sydney for wrecking. The car was running great with approx 168,00km on the clock, and only had some light suspension arm damage/guttered wheels at the rear, and some faded paint on the roof

Send me a PM or reply here if you're after anything here or any other random small parts. I'm located in Sydney for pickup or I can send most parts anywhere in Aus

Few more pics will be up during the week !

It had a few after market parts:

RPM / PBR Cushioned button clutch, pressure plate & recently machined flywheel, great condition, lots of meat left - $300

3" Kakimoto stainless steel catback exhaust, sensational condition - $300 pickup only

Front castor rods with near new urethane bushes installed - $50/pair

Blitz Dual SBC Spec-S, includes solenoid, all wiring looms - $350 ono

Return flow FMIC & piping kit for R33 Skyline Gts-t - painted black.

Pretty good condition, but the lower return pipe & end tank has some scrapes on the under side - $250 pickup only

Turbosmart boost gauge & Greddy a-pillar mount, Sensational condition - $100 ono

Walbro GSS-342 500HP fuel pump & R33 Skyline cradle, ready to drop in - $100

2x (pair) Avantek 18x8" wheels & tyres. Wheels are in sensational condition, basically no scrapes/damage at all - $250

One of the tyres is as new has about ~90% read, the other one has some camber wear and is probably not roadworthy

Pedders lowered springs & Pedders comfort gas shocks all round. Great condition - $400 for the full set

Adjustable front castor rods - $75

HKS pod filter & 3" AFM adapter - $40

Blitz turbo timer & wiring loom - $30

-----------

5 speed manual rb25det gearbox - SOLD to a mate

Rb25DET engine - ran perfectly while in the car & had great compression - approx 155 psi on all 6 cylinders - $1000

Will be sold as a long motor - no turbocharger, loom, coilpacks or accesories (alt, p/s, a/c pump) but everything else is there

Exterior Stuff:

s2 front bar & foglights/indicators, has been cut for FMIC - $300 pickup only

s2 front grille - $60

s2 front reo bar - $120

s2 bonnet - $250

Front guards - $75 each

Bare nose cut/radiator support - $150

Side mirrors - $40 each

Tail lights - $40 each

Standard sideskirts & matching rear pods - small crack/hole in one side - $120 - pickup only

Engine / Engine bay stuff:

Aircon condenser - $100

R33 radiator & shroud - $100

R33 aircon compressor pump - $100

R33 power steering pump - $100

R33 alternator - $90

A/c condenser/thermo fan - $60

engine clutch fan - $60

S2 afm (pink sticker) - $70

standard BOV & crossover pipe - $50

Engine Mounts - $60/pair

Fuse box lid - $20

Radiator overflow bottle - $20

Washer bottle & motors - $20

Brakes/driveline:

Front calipers, painted silver. Includes all pins/clips - $250

Rear calipers, painted silver. Includes all pins/clips - $120

Front rotors, used but good condition - $50/pair

Rear rotors, used but good condition - $50/pair

Front lower control arms - $50 ea

Front upper control arms - $50/pr

Front 5 stud hubs - $50 each

Rear lower control arms - $40 each

Rear 5 stud hubs - $120 pair

Handbrake drum assembly incl cables - $120 pair

Rear differential (4.1) manual diff - $175

Driveshafts $75 pair

Spare space saver wheel - $50

Interior:

S2 steering wheel & airbag - Great condition, little/no wear - $150

Driver's side power window switch (12 pin) - $75

Driver's side power window switch surround plastic (s2) - $60

Passenger side window motor - $50

Drivers side window motor - $100

Instrument cluster, approx 168,000km, all gauges working well - $100

Instrument cluster dash surround (s2) - $80

Gear stick surround (s2) - $50

Centre console, with good lid/latch - $50

Seatbelts (full set) - $75

Ignition barrel + door barrels & key - $90

on your kakimoto catback, on the pipes (not the cannon) is there a small rectangular plate with something like a product ID, perhaps starting with N----------- ???

PMs replied. Engine loom, p/s pump, front seats sold, Exhaust sold pending payment.

The adjustable castor rods are Tein, pictured below

Few more photos:

Pedders suspension:

post-35556-0-10302700-1376210837_thumb.jpg

Tein adjustable castor rods:

post-35556-0-91237700-1376210844_thumb.jpg

Sideskirts/pods

post-35556-0-32085200-1376210867_thumb.jpg

Hey mate.

How much for the boost gauge or cup without gauge and cigarette lighter socket?

What suburb is pickup? I might be interested in boot lining stuff if you have it in great condition too.

Cheers

-Steve

Hey mate.

How much for the boost gauge or cup without gauge and cigarette lighter socket?

What suburb is pickup? I might be interested in boot lining stuff if you have it in great condition too.

Cheers

-Steve

PM sent & replied !

Hey can I see some pics of rotors on 0401957814?? Front and rear?

No worries, i'll message you a pic on thursday

Hi do you have red stop light for rear spoiler? if so how much? thanks Dennis 0403922737

Yes i've got one - $25? PM me if you're keen

Do you still have the front seats?

Sorry mate i'm hanging onto them

Can u post up what's been sold ?

Most of the front end- bonnet, front bar, headlights, reo bar, engine wiring loom, front LCAs, gearbox, tailshaft, front/rear seats, door trims, PBR clutch, 3" kakimito exhaust, dash surround, power steering pump - SOLD

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The car/ECU will have all the sensor that it needs and expect to have. I think i do not have to explain to you how the Link is way better specialy if you have swapped engine   I just do not want to deal with any "problems" cuz i have only Nistune which i learned is not that great and in my case cant even deal with that speed problem (Link can) And of course it will be way more easier to tune and diagnose and safe. And for the ECU/speed problem...i dont know.
    • Per Mark Roberts of Sonictune: Mark Robert Author At this time, no. No ETA either 2016-17 models. You will be able to purchase and install a 2018.5+ TCU though   TCU purchasing and pricing info! As we near the release of TCU tuning, I am going to answer some questions I get asked often.   What do I need for TCU tuning? At this time, you will need a 2018.5+ TCU to be able to tune. If you have a 2016-to early 2018, you will need to replace your TCU with the newer version. One good way to know if your TCU is good is if you have auto upshift in manual mode in 1st gear around 6500 rpms. If your manual 1st gear goes to 7k rpm and will hit the rev limiter unless you shift, you have the older TCU.   Why do I need to buy another ecu license/phone flash if I already have it on my ECU tune? The TCU is its own computer module. It is completely separate from the ECU. Because of this, you will be required to purchase a TCU license and, if your tuner has it, the phone flash license required to tune it via phone/bluetooth.   Do I need TCU tuning? TCU tuning is NOT required. However, the faster your setup, the more it will assist in track and dragy time consistency.   If I’m ECU tuned by (tuner A) can I get my TCU tuned by (Tuner ? Yes, since it’s a different module and a completely separate flash, you can have two different tuners. However, it is highly recommend that you have both tuned by the same tuner. For me, my TCU tuning will directly complement my ECU tuning style and features and running my ECU and another TCU or vice versa MIGHT cause some issues. At this time and for the foreseeable future, I will only be tuning my current ECU tuned customers TCUs.     I have a SYVECS AWD controller. Do I still need it? Yes! The AWD controllers main job is to control your AWD system. However, with TCU tuning, you will no longer need the auto-shift function as that will be done through the TCU. The AWD controller will still be very beneficial for racers looking to maximize traction on the launch.     Shift schedule changes: holding gears longer at lower pedal input as well as max shift rpm changes. Please note, the new ECU race rom coming out will address 90% of the shitty drivability issues these cars have through custom maps from myself and Racebox—as well as others I am sure.   Increase shift speeds: as seen in the videos I’ve been posting, the TCU shifts much faster once tuned.   Increased shift pressures: as also seen in the videos, much firmer full throttle shifts.      
    • Per Mark Roberts of Sonictune:     Mark Robert Author At this time, no. No ETA either 2016-17 models. You will be able to purchase and install a 2018.5+ TCU though   TCU purchasing and pricing info! As we near the release of TCU tuning, I am going to answer some questions I get asked often.   What do I need for TCU tuning? At this time, you will need a 2018.5+ TCU to be able to tune. If you have a 2016-to early 2018, you will need to replace your TCU with the newer version. One good way to know if your TCU is good is if you have auto upshift in manual mode in 1st gear around 6500 rpms. If your manual 1st gear goes to 7k rpm and will hit the rev limiter unless you shift, you have the older TCU.   Why do I need to buy another ecu license/phone flash if I already have it on my ECU tune? The TCU is its own computer module. It is completely separate from the ECU. Because of this, you will be required to purchase a TCU license and, if your tuner has it, the phone flash license required to tune it via phone/bluetooth.   Do I need TCU tuning? TCU tuning is NOT required. However, the faster your setup, the more it will assist in track and dragy time consistency.   If I’m ECU tuned by (tuner A) can I get my TCU tuned by (Tuner ? Yes, since it’s a different module and a completely separate flash, you can have two different tuners. However, it is highly recommend that you have both tuned by the same tuner. For me, my TCU tuning will directly complement my ECU tuning style and features and running my ECU and another TCU or vice versa MIGHT cause some issues. At this time and for the foreseeable future, I will only be tuning my current ECU tuned customers TCUs.     I have a SYVECS AWD controller. Do I still need it? Yes! The AWD controllers main job is to control your AWD system. However, with TCU tuning, you will no longer need the auto-shift function as that will be done through the TCU. The AWD controller will still be very beneficial for racers looking to maximize traction on the launch.     Shift schedule changes: holding gears longer at lower pedal input as well as max shift rpm changes. Please note, the new ECU race rom coming out will address 90% of the shitty drivability issues these cars have through custom maps from myself and Racebox—as well as others I am sure.   Increase shift speeds: as seen in the videos I’ve been posting, the TCU shifts much faster once tuned.   Increased shift pressures: as also seen in the videos, much firmer full throttle shifts.      
    • The fancy pants red shock tower brace is finally incoming from MX5 Mania, getting it shipped from 'Merica has been a long and problematic process, and GWR, the 'Merican supplier will not ship directly to consumers outside of the US, Mania basically had to order a heap of them, the colour choice was silver, or red, and we all know anything red adds 5 killerwasps of dynotorques..... Whilst it does fit over a 2.5, and I've seen a few photos and videos of it being installed and fitting, google also says it might get real close to the FAB9 intake front runner, people in the US says it does fit with the FAB9 intake, except for one person who said it slightly touched.......so there is that.....LOL..... As it seems that I am the first in AU to have this combination of parts there's no local knowledge about fitment, so I'm just a willing guinea pig in this endeavour, I'll cross my fingers and toes and hope for the best In other news, I ordered stuff from China  on the same day I ordered the 23° silicone bend from Victoria, the stuff from China arrived a day ago, the 23° silicone bend is still travelling around Australia thanks to Australia Post, and "may" be here next week
    • Very good news...I contacted Racebox about it last night. My car is a 2016 so remains to be seen if it is compatible, requires a TCU swap, or is impossible.
×
×
  • Create New...