Jump to content
SAU Community

Hicas Delete Kit Which One?

JDM_R32_R35
 Share

Recommended Posts

JDM_R32_R35 Enthusiast

JDM_R32_R35

Posted
Posted

Hi, I am planning to buy a R32 GTS4 HNR32.

Which hicas delete kit do I need?

http://www.ebay.co.uk/itm/MIDORI-SEIBI-HICAS-CANCELLER-KIT-NISSAN-Skyline-HCR32-RB20DET-R32-GTST-/151029698805?pt=AU_Car_Parts_Accessories&hash=item232a1250f5

http://www.ebay.co.uk/itm/MIDORI-SEIBI-HICAS-CANCELLER-KIT-NISSAN-Skyline-GT-R-BNR34-RB26DETT-R34-GTR-/181124222008?pt=AU_Car_Parts_Accessories&hash=item2a2bd84c38

Link to comment
https://www.sau.com.au/forums/topic/429971-hicas-delete-kit-which-one/
Share on other sites
JDM_R32_R35 Enthusiast

JDM_R32_R35

Posted
  • Author
Posted

They're both the same I believe. Buy the HCR32 one (first link), that way, if there are any issues, you can't be told you "bought the wrong item".

So AWD and RWD are the same in Hicas design?

D.I.Y. Mik Veteran

D.I.Y. Mik

Posted
Posted (edited)

yeaow! $$$$ Neither do away with the outer ball joints.

So its no better than a cheap ass lock bar

Driftworks

post-89755-0-36937400-1376443637_thumb.jpg

No more ball joint

Keep in mind they are selling chinese crap, so only get what you need from them.

My Driftworks radius rod is stuffed after 6 months of street driving, they dont want to know about it.

Their customer service is REAL bad, i got wrong brakelines, 4 months to sort it out.

So.... Good luck

And just jap have a handy little fitting for looping the hicas lines

Edited by D.I.Y. Mik
ZRBE Experienced

ZRBE

Posted
Posted (edited)

Are there different types? I only have a single black bar that sits in the middle of the HICAS system underneath my car..

These look very different..

Mine still looks stock on both ends, while these in OP's link look nice, black and shiny.

Edited by Zrobe
GTSBoy Grand Master

GTSBoy

Posted
Posted

The HICAS bars are a "lock". Just replace the actuator with something that doesn't actuate.

The delete kits are actually a "delete". You can do what the hell you want with the actuator (leave it, bin it) and the new parts you buy replace the old HICAS tie rods. The clever ones also replace the tie rod ends (by putting bushes into the steering arm holes), just like a non-HICAS rear end (which is still the bestest way to do it).

ZRBE Experienced

ZRBE

Posted
Posted

The HICAS bars are a "lock". Just replace the actuator with something that doesn't actuate.

The delete kits are actually a "delete". You can do what the hell you want with the actuator (leave it, bin it) and the new parts you buy replace the old HICAS tie rods. The clever ones also replace the tie rod ends (by putting bushes into the steering arm holes), just like a non-HICAS rear end (which is still the bestest way to do it).

So your saying mine would just be the most basic one you can get?

Don't suppose you know who sells the ones with the bushes.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • perry_r33
      R34 GTR Vspec Garage Sale - All must go!

      By perry_r33 · Posted

      Pm sent 
    • Robot
      Skyline v36 350GT sedan hunting on idle

      By Robot · Posted

      Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...