Jump to content
SAU Community

Recommended Posts

Posted by Merli  

Zaino is good... Very durable, but it doesn't have the depth of shine as the other carnauba waxes that I listed on the first page.

It's good, make no doubt, but you have to apply like 4+ coats to get a nice deep gloss out of it... and even still, it's not as good as one application of a good professional carnauba wax.

Come on Merli,

This is not too shabby for a single coat.

r33gtr_roof2.jpg

  • Replies 44
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Come on funkeh....

Hardly a fair comparison, totally different lighting conditions.

DSCF0275.JPG

Joel,

Car covers are a real pain in the neck. They are only good for storage or cars that don't get driven very often. I am betting on you cracking the shites after a week.:P

A good wax that is available in stores in Australia is Meguires number 26. It's the one in the beige bottle without all the marketing crap on it.

Don't know if it had been mentioned already.

Also, as it was already pointed out, a clay bar should only be used maybe twice a year, the exceptions are when:

- a bird shits on the car and it dries up

- you park under a tree that is dripping pollen all over your paint

Remember to lube up good and then park in a garage and you shouldn't need it that often.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
×
×
  • Create New...