Jump to content
SAU Community

Recommended Posts

hi all,

so i have a power fc for my s15, im looking into the R35 GTR MAF. i know there are more modern computers out there, but this is what i have and i would rather make this work.

so i have been reading heaps about the R35 maf's and their capabilities, they are cheaper then the z32's and more responsive suposably.

there is also this option

http://www.pmas-maf.com/mass-air-sensors.php

i see a few people have dabbled with the r35 and the HPX, but i cant seem to find any data for the R35 MAF.

the hpx website supplies flow rates vs voltages.

there is also nistune who put up this

http://forum.nistune.com/viewtopic.php?f=10&t=2428

however it would seem that the HPX will support a much higher HP number then the r35.

myself personally would prefter the r35 maf to support a smaller turbo with streetablilty.

does anyone know how to scale the power fc (FC DATALOGIT) air flow readings?

and or convert from lbs/min to PFC data?

and

R35 MAF flowrates to PFC Data...

Cheers,

scott

what i reallly need after all that is the following data for the R35 GTR MAF,

voltage vs flow

i cant find that info anywhere !!!

if i can get that, i can get a close scale to put it into the PFC, i have found the nissan polynominal to make adjustments, and then fine tune to suit my car once in there. but just need the data first up.

even resistance / voltage woul dbe a good start to work it backwards with interpolation to the stock afm.

there is a lot of talk about it on forums, but actual hard data is a mission to come by for this MAF.

Cheer.s

my bad.... still a bit of a steep learning curve here.

but with some form of units of data ya can interpolate it.

the HPX gives lbs/min flow vs voltage.

idealy that would be awesome to get from the R35 GTR MAF....

if anyone out there has it?

Nistune has VQ maps for all the AFMs in the installation (OK, probably actually in the ROM Pack, but no matter). You can install Nistune and look at the Z32 one, noting down the VQ maps, then you could do the same with the R35 AFM VQ map. You could even load up a map for a Z32 VG30DET then use the software to do a change to the R35 AFm and not the changes that it makes to the k value and so on. That would instruct you quite well on the relativity between them.. If you couldn't parley that data into a useful starting VQ for your PFC I'd be very surprised.

f**king legend !

i was going to install nistune tonight and have a poke around at a whimb to see if it would have any data i could use.

thanks for clearing that up!

that will be a good start,

and to be honest, that will most probably be pretty close!

then a tune of the fuel map to clean it up.

cheers

The VQ AFM's are very similar to the R35 ones, and can be had very cheap these days. If there is data around for them they would be a no brainer over the Z32.

VQ afm????

Voltage Quantifier (VQ) ???

i will have hte data conversion from the r35 later with any luck.

the R35 are about 90 odd $ then an adaptor welded to a pipe and voila!

so the question is, where did you find the Flow table vs voltage to tune the thing?

so i have interpolated with averages between nistune and apexi.

fark... its rough as guts, but it could be a start...

iv contacted apexi to see if they have any data i can use.

;) ya onto it now.

yep im tuning it my self.

hence why im trying to get as much data as i can ;)...

and yes your right. once the curve is pretty right with respects to resolution. you can fix up the fuel map to suit the needs of the tune.

the tuning side isnt the concern, just the R35 afm data is lol!

  • 1 month later...

post-17056-0-33137200-1381981458_thumb.png

ok so since we last spoke sau...

i bought an official APEXi kit, from streeter who was very helpful as always..

it comes with the flow data to punch into the pfc for maf calibration,

how i interpolated the nistune data, was obviously incorrect....

you can see my the graph attached the r35gtr right and left banks is my interpolation of the nistune data.

unfortunatley i f**ked that up somewhere. and its always easier to get data from someone who has actually tested and aquired it.

so i decided to go this route for something different, its cost is a bit cheaper than a Z32, and i wont be aiming for anything near 300rwkw (about what hte z32 can handle on a sr apparantly - no idea. never tried or seen)

so thought id throw this up for the benefit on anyone else going down this path with a power fc..

cheers.

  • 3 years later...

A bit old, but still the most informative bit of info I have come across when it comes to calibrating the R35 MAF.  

But, still not enough I think.  

I have a power fc, datalogit, and am hoping to throw a R35 MAF onto my RB25 R32.  There are many more options for R35 MAF adapaters now and the aforementioned APEXi kit is pretty ugly.  Someone is selling the MAF data separately on yahoo auctions, but if I can enter the info myself it would be helpful. 

Does anyone have any ideas of how to enter the above graph info numerically into the power fc? 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • If they can dyno them, get them dyno'd, make sure they're not leaking, and if they look okay on the dyno and are performing relatively well, put them in the car.   If they're leaking oil etc, and you feel so inclined, open them up yourself and see what you can do to fix it. The main thing you're trying to do is replace the parts that perish, like seals. You're not attempting to change the valving. You might even be able to find somewhere that has the Tein parts/rebuild kit if you dig hard.
    • Can you also make sure the invoices on the box (And none exist in the boxes) are below our import duty limits... I jest, there's nothing I need to actually purchase and order in. (Unless you can find me a rear diff carrier, brand new, for stupidly cheap, that is for a Toyota Landcruiser, HZJ105R GXL, 2000 year model...)  
    • Murphy strikes again! Nothing at all would have gone wrong if you had the tool kit in the car! You'd have just found the clamp loose the next time you went to touch it...
    • I have been being VERY quiet about what you're alluding to, as it is something that ticks me off... The number of cars from factory that run coil overs is HUGE! Most of them these days do... The other part that annoys me, is people saying "Well all the incabin adjustable suspension is illegal by blah blah blah"... If that's the case, then why can I buy a car brand new that can do it if, FULL STOP in cabin adjustable suspension is illegal...   Also, I could just chuck some aftermarket shocks in my car, throw the stock springs on, after my blue slip, dump my super low springs back in. Same shock and spring style setup... Hell, they could also be the same colour springs etc.     I'm voting, BlueSlipper didn't want to touch the above car for some reason. Whether it be some sort of bias against the car, the owner, them maybe having previously done dodgy shit and now they're being super careful in case they get slapped in the face by the Gumbyment again... Find a new blueslip place.   And can confirm as you had said, yes there are holy bibles of vehicle heights, and all sorts of other suspension stuff. Heck your run of the mill mechanic, and tyre shop has access to all of that stuff. It's how they do wheel alignments...
    • Funny story Heading to Sydney this morning on the HWY there was some slow traffic, so I gave it the beans and midway through my overtaking "power run" I lost all power It seems that I missed a hose clamp,  and the MAF and filter went WiFi To make this more problematic, the little tool kit that lives in the boot, is sitting in the sun room at Goulburn......LOL Luckily for me I found a bit of steel on the side of the road that could be used like a rusty and bent flat head screw driver to tighten it up enough that it got me into Sydney, it is now all tight like a tiger with the aid of a 8mm socket Note to self: Use my brain and double check stuff, and always keep that little tool kit in the car for when I have a brain fart
×
×
  • Create New...