Jump to content
SAU Community

Recommended Posts

I Thought i would start this to help all of us that own RWD Stageas...

It would be good to keep it only RWD so it can be an information source for people that need help with part and other bits

These are some things i know so far

I will edit as i go to fill in the gaps and if there's new info that would be great

Upgrades can be listed as well as stock part

Front Brakes: -Calipers = Unknown Upgrade:GTST r33

- Rotors = Unknown

Rear Brakes: -Calipers = Unknown

- Rotors = Unknown

Suspension: -Tension/caster rods: 300zx,R33, R34 (and many more i think)

-Tie rods and ends = S14,S15

-Other rods etc: Unknown

-Front Springs: Unknown

-Front Shocks: Unknown

-Back Springs: Unknown

-Back Shocks: Unknown

Gear box: -Auto: r34/s2stagea

Edited by Tw1ch

Yeah, they are: Myles (GreenGhost) just bought and fitted a new set of HSD coilovers, and the fronts were the same as S14. Bonus for him was adjustable camber tops: My RSFour set didn't get them...

FYI: he also managed to get R34 GTT front calipers to fit with a little bit of fiddling.

Rear suspension is the same on both 4wd and RWD, as far as I am aware: Told Myles to get his lazy self back on the forums and give you as much info as he has: give it time - He'll get around to it.

r33 front brakes and rotors will fit with a wahser/spacer to line then up

rear brakes r34 will fit straight up

rear shocks are the same as 4wd

fronts shocks are s14

gearbox is same as r34

ottomoto do coilovers for s2 rwd and are awesome

  • 2 weeks later...

Another RS S2 owner signing in.

All I can add is that an RB30 will drop straight in with no drilling of mounts using stock manifold.

Cant fit the strut brace on without spacing it up, or perhaps a non traction control throttle body would give a little more clearance.

Unless the 2wd has an entirely different suspension to the 4wd all he will be adjusting is the angle of the shocks - not the camber.

Yeah, they are: Myles (GreenGhost) just bought and fitted a new set of HSD coilovers, and the fronts were the same as S14. Bonus for him was adjustable camber tops: My RSFour set didn't get them...

FYI: he also managed to get R34 GTT front calipers to fit with a little bit of fiddling.

Unless the 2wd has an entirely different suspension to the 4wd all he will be adjusting is the angle of the shocks - not the camber.

2wd front is entirely different. It is mcpherson strut, strut towers also look different.

Can also add that the whiteline rear swaybar does fit, but you need to slot out the u brackets a bit and make some spacers (about 15mm per side) to straigten up the links as the rs rear end is wider for some reason. You can get by without the spacers, but the links are on a crazy angle and I wouldn't recommend it.

  • 1 month later...

Another addition, as the front suspension is different, the info for s2 brake conversions doesnt apply to rs. The mounting holes are 12mm, so the same options are a direct fit as for an s1, eg r33 brakes. I wanted to use 34gtt brakes, and made new inserts for the callipers with an m12x1.25 threads rather than drilling out the knuckles as some guys have done. If anyone wants a photo or info let me know, but if you look at the callipers its pretty obvious :)

  • 2 years later...

WHile this is an old thread by 2+ years. This is what i have found out about the rwd stagea,

- They use the McPhersons strut front suspension setup of the S15 (Bottom arm, 5 stud hub, shock etc)

- They have a 2 pot brake caliper and 280mm S14/S15 rotors

- The rear has no hicas

- Has an S15 rear subframe/arm setup (S15 hubs, S15 style subframe I Have measured this.

- Uses an R33 internal drum handbrake with an S14 style single pot sliding caliper

- Diff 4:1 VLSD

Other stuff I found out:

- 296mm R33 GTST Callipers/Rotors bolt straight up which means 33GTR Brembo's/350z Brembo's will too

- R34 GTT callipers/rotors WILL NOT fit, unless you drill out the hub as the calipers use larger bolts

- S14/15 adjustable rear arms etc all fit

- Uses S-body/R-body suspension bushes

- Tension rods are S14/15-R33/34

- Tie rods and ends are S14/S15

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...