Jump to content
SAU Community

Mugabetown - Whoretownin' At It's Worst.

t5iv

By t5iv,
in Queensland

 Share

Recommended Posts

Ants Grand Master

Ants

Posted
Posted

So problem number one............

There is a knocking noise from the rear when I brake or put the car in reverse. The best way I can describe is like backlash from within rear driveline, a bit like a weight being pushed forwards then going backwards. Its not a harsh noise.

I have had this problem ever since I have owned the car.

It does not happen all the the time but I would like to get rid of this pesky issue.

Im thinking the rear diff is the culprit.

Anyone have any thoughts?

  • Replies 24.4k
  • Created
  • Last Reply

Top Posters In This Topic

  • Ants

    5677

  • Captain Natro

    2067

  • t5iv

    1789

  • Cadmoon

    1709

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

Smity42
Smity42

FYP

Cadmoon
Cadmoon

Some bored car photos from today

Smity42
Smity42

Become a member, you tight-a*se

Posted Images

Captain Natro Grand Master

Captain Natro

Posted
Posted

So problem number one............

There is a knocking noise from the rear when I brake or put the car in reverse. The best way I can describe is like backlash from within rear driveline, a bit like a weight being pushed forwards then going backwards. Its not a harsh noise.

I have had this problem ever since I have owned the car.

It does not happen all the the time but I would like to get rid of this pesky issue.

Im thinking the rear diff is the culprit.

Anyone have any thoughts?

How olds the diff, could be getting play in it and you're hearing the slop as it goes from forward to reverse and back again

Ants Grand Master

Ants

Posted
Posted

I don't know about Cusco.

What I do know is that most 1.5 / 2 way jap diff tend to be a bit tough and clunky (friction plates)

With helical there is none of that and therefore is just smoother and runs quieter

sneakey pete Grand Master

sneakey pete

Posted
Posted

Diffs are a bridge i'll have to cross at some point soon-ish i think.

You'll have to re get your exemption won't you?

Also, I have a hard decision to make. GC hinterland or Mt Nebo

Up tambo, down tambo, up Oreilleys... ah f**k this roadworks and the 1 lane road, back down Oreilleys, up tambo, down tambo...

Stopped in at Cedar creek on the way back down too, i think i'll have to bring boardies and a towel next time.

If I had today off I would come with you Pete

I'm not sure my car's good enough to be seen with yours (once you get it finished at least!)

Ants Grand Master

Ants

Posted
Posted

Diffs are a bridge i'll have to cross at some point soon-ish i think.

Up tambo, down tambo, up Oreilleys... ah f**k this roadworks and the 1 lane road, back down Oreilleys, up tambo, down tambo...

Stopped in at Cedar creek on the way back down too, i think i'll have to bring boardies and a towel next time.

I'm not sure my car's good enough to be seen with yours (once you get it finished at least!)

probably one of the most underated mods you could do IMO.

Will do front one too after my bank account recovers.

Zac will be busy.

Well she is kinda finished. I'm even taking it with me to work FTM.

Just need to respray rear bar.

My car would be fine with yours or any other Nissan. Just no commodores

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • Duncan
      Boost cut after swap(RB25DET NEO) R34

      By Duncan · Posted

      Can you clarify what you mean by boost cut, do you mean it misfires both when under load (driving) and when stationary and out of gear? Or does the ECU pull power when it reaches a specific boost level that is too high (boost control issue)? Does it occur at idle with no throttle? When you say "the ECU is OK", what ECU is it and why do you think it is OK? Have you used the NEO ECU, and if so do you have a MAP sensor attached? Same for the AFM, why do you think it is OK? Do you have any way to put a fuel pressure gauge on it (even just a mechanical one between the fuel filter and fuel rail)?
    • Kapr
      Boost cut after swap(RB25DET NEO) R34

      By Kapr · Posted

      Hi.. Just another problem. So maybe you can help. I(my mechanic) done swap from my RB20DE NEO to RB25DET NEO. Everything is OK but we have a boost cut. Coils/Plugs are ok...AFM is ok. ECU is ok. I have Walbro 255 but it "changed" sound few months ago(you can hear it ouside) you did not hear that when it was new(maybe faulty?) Sooo...what now? What can cause this boost cut? It is even when you standing still...
    • BOLGE
      R34 Plug Identification

      By BOLGE · Posted

      legend thanks mate !
    • fatz
      Neil's R33 Gts-t Build

      By fatz · Posted

      Skidz
    • iamhe77
      Might import a stagea

      By iamhe77 · Posted

      Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
×
×
  • Create New...