Jump to content
SAU Community

Mugabetown - Whoretownin' At It's Worst.


Recommended Posts

Spent 2 days on the o2 sensors.

$100 on specialty tools and a few skinned knuckles later, I have 1 o2 out FML.

Avoided engine out tho :P

Not engine out??? But I don't understand... :blink::P

Not great no, but it wasn't exactly economy driving either. I imagine quite a bit of fuel would be flowing when its developing 400hp.

Should probably put O2 sensors in to help that. Presumably there's only 1...?

wut? usually there are two 02 sensors on RB26

Strangely enough I only have one now that I could spot under my car

Found the second one on the top of my dumps, can't figure out what is going on with the plugs though. Got a pair of 3 wire ones, one flat plug one square.

edit: images

WP_20140714_0111_zpsa09800cb.jpg

Couldn't for the life of me find another 3 plug one like the top one. Dunno where i'd be supposed to plug the second sensor into then...

Found the second one on the top of my dumps, can't figure out what is going on with the plugs though. Got a pair of 3 wire ones, one flat plug one square.

Couldn't for the life of me find another 3 plug one like the top one. Dunno where i'd be supposed to plug the second sensor into then...

Nissan made it idiot proof, the plug on the front o2 is flat and the plug on the rear o2 sensor is square

Defeated my o2s finally. Another custom tool for the collection.

now im guna need a new 22mm spanner...

I live my life a 1/4 of a 1/4 of a turn at a time

Edited by MagicMikeZ32
  • Like 1

Turbo xxxx ECU, injectors, fuel pump, FMIC, Hi flow cat (perhaps)

R34 Turbo Brodi $200

Turbo Highflow, Hypergear, $860

Braided Turbo Oil Line, Hypergear, $88

High Preasure Actuator, Hypergear, $120

ECU, Haltech Platinum Pro Plugin, $1,975

Flex Fuel Sensor, Haltech, $250

Injectors, ID1000's, $720

Fuel Pump, Nismo Intank, $385

Fuel Pressure Regulator, Nismo, $132

Highflow Cat, Venom, $250

Tuning, ???, $1,000

Total $5,980

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Was that with the cas upside or correct way up?
    • Did and sync timing with light 
    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
×
×
  • Create New...