Jump to content
SAU Community

Mugabetown - Whoretownin' At It's Worst.


Recommended Posts

I did happy laps in a POS XF ute...

My mate did it in a second Gen magna...

so all im getting from this is that you want an SAU non skyline/R35 Happy Laps?

Cm'on boys snap out of it.

A reliable source tells me the X181 and the Powerbow gen X are in fact the same shape. So a long sweet spot starting low and heading up to traditional centre. They are however scalloped to make them a little lighter, meaning if you hit off center you lose some power. The Matrix has a similar length middle but is not scalloped and therefore a little heavier but is more forgiving if you get one off center. I would give both a go, if you can live with the extra weight on the matrix it may be the go, if anything I wish my bat was less scalloped.

Thanks broski.

I tend to hit most balls off center I reckon :P, so the matrix is probably a better bet. But the x181 is available quite a bit cheaper due to being an old model...

I believe it's an hourly charge, it takes quite a few hours to tune from scratch. A lot of the cost is because dynos are f**king expensive to buy.

dont most aftermarket ecus come with a basic set up,enough to get you to the tuners,so as long as nothing goes wrong or need replacing,wouldnt it only take a couple of hours the most?,just asking as interested in the process,im not a bean counter but do like to see where the moneys going.Do they all cost this much or is it mainly on the first tune?If so ill have to save rather hard for the tune.in the future,hopefully not to far away,work in progress.

dont most aftermarket ecus come with a basic set up,enough to get you to the tuners,so as long as nothing goes wrong or need replacing,wouldnt it only take a couple of hours the most?,just asking as interested in the process,im not a bean counter but do like to see where the moneys going.Do they all cost this much or is it mainly on the first tune?If so ill have to save rather hard for the tune.in the future,hopefully not to far away,work in progress.

all depends on the type tune mate.

I've had tunes costing $600 to $2k+

All on different ECU applications

Different engine setups ie turbos, cams,exhaust, intercooler, boost controller etc....

The more ancillaries you have in board generally the longer the tune and cost

dont most aftermarket ecus come with a basic set up,enough to get you to the tuners,so as long as nothing goes wrong or need replacing,wouldnt it only take a couple of hours the most?,just asking as interested in the process,im not a bean counter but do like to see where the moneys going.Do they all cost this much or is it mainly on the first tune?If so ill have to save rather hard for the tune.in the future,hopefully not to far away,work in progress.

The big factor for mouse is that he's tuning it to run on e85 as well. Essentially a tune on pump then a tune on a mix, then on full e85. Takes time hence the money.

The big factor for mouse is that he's tuning it to run on e85 as well. Essentially a tune on pump then a tune on a mix, then on full e85. Takes time hence the money.

This. I always knew a proper flex tune would be expensive.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • How would you even adjust the clutch if the pedal already has the correct free play? The operating cylinder has no adjustment in mounting position or rod length. On pull style clutches there is also no ability to adjust the bearing carrier. Push type I can see how adjusting the carrier height makes it all work.   If this is the twin plate clutch did you verify that your friction disks were oriented correctly? It's not mentioned in the directions at all you just have to notice that one side the friction disks have a part number on the hub fingers and a subtle coning to those fingers. Another thing that I noticed was if you put the friction disks in backwards the pressure plate fingers will not be even and flat when the clutch is installed.
    • yeah, mechanically, it is probably do-able, off the top of my head, there would be the transfer case, which I believe will bolt up to the rear of the RWD transmission, the shorter rear tail shaft. A front drive shaft, front diff, engine upper sump, front drive shafts, front hubs and front AWD struts (they are shaped around the front drive shafts), LCAs (at the very least from the front suspension) oil cooler.  You might want the rear diff from an AWD too, so you can be certain the front and rear diff rations are identical.  Who knows what brackets and mounts you might need.  So a whole doner car might be the best option if you need to maintain RHD. Then actually making it work, that would be a whole different story.
    • Take the fall as a warning sign for future endeavours  Stay safe mate
    • hi mate, HKS cooler piping still available by any chance?
×
×
  • Create New...