Jump to content
SAU Community

Recommended Posts

Hi all,

I need a new HD clutch soon and have noticed that the Exedy ones are about $150-200 more then the RPM equivalent.

Is it worth it to spend the extra on the Exedy or is there really no difference?

I basically just need a clutch that can handle up to 230rwkw so hoping that either HD will be ok.

Thanks.

DO NOT get the Exedy Heavy Duty Range, the pink pressure plates, they're rubbish.. make sure it's the silver cover which is made in Japan.. not a remanufactured OEM item that is sprayed pink.

I bought my car with an RPM clutch and it was slipping hard (due to uneven wear) so I removed the clutch kit and replaced it (my only experience).

I've got an excedy heavy duty, I don't know which model but when I did the engine swap and moved the clutch over it was about 75% worn (hard to tell) and the pressure plate is pink. I just tuned up to 240rwkw and it doesn't just bite any more theres a split second of slip. 3rd gear won't stall the motor any more, if I let it out in 3rd on boost it will just slip.

Is my clutch on the way out? I'm going for 300rwkw at the end of this year, not sure whether to do it first. Lots of people say over 300 is fine with this clutch but i'm not convinced

Blackkers, chuck it into 4th gear and boost up a hill. You will either notice it slip or it won't slip and that's how I would determine.

My pink excedy lasted a few power runs on the dyno before giving up on the way home on the highway. This was 250rwkw

I am currently running a KB clutch from KB clutches in Sydney. Great service and amazing price, just call him and send him a dyno sheet or some specs of the car and he will do the rest

Okay mate I'll definitely give it a go. I know the clutch has a bit of meat on it i'm just not sure how it will handle the power i'm chasing. Thanks for your input

KB seems to be the place for clutches too

Edited by Blackkers

Got the RPM in the end, haven't fitted it yet but it looks pretty decent.

Honestly couldn't justify spending almost double on an exedy.

Good luck mate, hope they have revised their clutches. They had a bad run for a while, and I was one to suffer from it.

It depends on where u buy the clutch from i guess

i bought a new hd exedy clutch and gtr racing flywheel for 925 shipped to my door and it only took one day.

call this number and ask for simon and tell him josh from armidale gave u his number 0296481688

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Stock ECU (or more accurately stock tune) absolutely refuses to go over 10psi and behaves like you have seen. The Nistune is the same if it is the stock tune. If the Nistune chip has been tuned, the resulting tune could be literally anything for any combination of parts. The Nistune just makes the stock ECU Tunable.
    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
×
×
  • Create New...