Jump to content
SAU Community

Recommended Posts

hey guys, wondering if anyone has come across this noise before

my na r34 make a whining noise at almost exactly 80km/h in 5th gear at about 1/4 throttle, it sould like i could be comming from the gearbox, cheaked oil levels and all seams fine

if anyone has heard this would love to find out what it is and if there is a fix

cheers

Link to comment
https://www.sau.com.au/forums/topic/432249-r34-whining-at-80kmh/
Share on other sites

probably, how could i cheak that? would it be a lack of diff oil or something messed up internally

If it's only doing the while in one gear (e..g 5th) then you can point at the gearbox. If it's whining in whatever gear at that speed (e.g. drop it to 4th and 3rd) then it's most likely diff. Does it whine under load or all the time (e.g. lifting off going downhill)?

Wheel bearings?

Yeah that was my first though when I saw this thread. I'd say check wheel bearings, though it does sound a bit strange that it's happening in a specific gear - in terms of wheel bearings.

Measure the diff gear backlash and replace shims where necessary. Replace the oil.

Although you could just be low on oil, it's best to do the job properly and check the clearances as the gears and shims wear over time.

The pinion bearings may need replacing also, this is a bit trickier.

ill see if it does it in other gears tomorrow on my way to work

it doesn't sound to much like wheel bearings because when i load them by weaving left to right it isn't any worse

what oil does it take do you know?

epx 80w-90 or multitrax?

I had this problem with my subaru. Eg. Is the same speed. Slower barely hear it. Faster gone. I changed the gearbox and it fixed the problem. Not sure if it was the gears meshing or the pinion gear. Id say that wheel bearings make a whirring noise not wining. Snd pinion gear id guess is the front diff. So I would say possible diff relation or gearbox. Hope this info helped.

Found out today what it was

Got it up on the hoist at work and ran it up to speed

Sound was comming from where the gearbox meats the tail shaft

I'm guessing there's a bush or baring in there that has gone

No noise comming from the box or diff

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
    • Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
    • Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
    • I also used NP   That’s were it’s seems to be the best place to fit it? All schematic shows also that it’s should be referenced from the turbo housing. But idk, I do see high hp cars without any connection or anything to their turbos, so I really don’t know how they connect their things
    • I do have loctite 243 and 246 and a few more models. I could drill it now in place and make new threads for m12 and order an4 - m12 coupling and fit that to the turbo. Run a braided hose to the EBC which I could get a an4 to 1/8npt 
×
×
  • Create New...