Jump to content
SAU Community

Rb26 Engine Parts (Perth)

rdd232
 Share

Recommended Posts

rdd232 Newbie

rdd232

Posted
Posted (edited)

Due to interest of individual engine components will now be parting engine out. Please send through your BEST OFFER and I will reply if it is reasonable. Will deliver all items to Perth metro area. Not willing to ship anything. Long motor-no cash no view!!! (e.g. If you do not have any money I will not give you my address!!!) I can not emphasise this enough!

Long motor with standard turbochargers attatched.

Motor was removed from my r32 gtr as a runner with suspected blown head gasket and low oil pressure. SUITS REBUILD!

Sump is removed and engine is standard.

Comes with wiring loom(poor condition) and original ecu.

Also have second set of turbochargers.

Will send more details/photos as required to genuine buyers.

Injectors sold.

Air con compressor sold.

Engine mounts ( rubber part ) sold.post-109321-0-15001800-1380415269.jpgpost-109321-0-62591600-1380415249.jpgpost-109321-0-77137500-1380415225.jpgpost-109321-0-44788200-1380415201.jpgpost-109321-0-09804100-1380415697.jpgpost-109321-0-78248100-1380415722.jpgpost-109321-0-12355400-1380415882.jpg

Edited by rdd232
Link to comment
https://www.sau.com.au/forums/topic/432497-rb26-engine-parts-perth/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      R34 GT-T cycling ABS pump

      By Kinkstaah · Posted

      The downside of this is when you try to track the car, as soon as you hit ABS you get introduced to a unbled system. I want to avoid this. I do not want to bleed/flush/jack up the car twice just to bleed the f**kin car.
    • MBS206
      33 GTR Broken front wheel knuckle

      By MBS206 · Posted

      But again, the engineers said your cast aluminium would be fine based on the load that would be stretching that section. Same load stretching the bolts in a flex (not the twist), with a much smaller cross sectional area than the original part you've broken. It's why you'd need to be using higher strength bolts, but that's just making up for the strength you lose with less area...
    • Dose Pipe Sutututu
      R34 GT-T cycling ABS pump

      By Dose Pipe Sutututu · Posted

      I am truly amazed someone on this planet was able to cycle the pump using a scan tool. I've always ghetto cycled them on Nissan 90s shit boxes by slamming the brakes and pulling the handbrake to agitate the rear wheels enough to cause a speed difference
    • joshuaho96
      R34 GT-T cycling ABS pump

      By joshuaho96 · Posted

      I didn't actually try it at the time but a Launch X431 with the appropriate software licenses/upsell will have the ABS bleed function. The Consult II you can still find some old sets of equipment but they're really, really expensive:   
    • R32 TT
      33 GTR Broken front wheel knuckle

      By R32 TT · Posted

      Well I'll start by saying I'm not an engineer. I am going to go with the KiwiCNC ones.  They are made of 7050 alloy have good fillets and radius.  The material alone is in the order of double the strength and fatigue resistance - Those bolts, once torqued correctly place most of the load at the flat face of the mating surface - the 'stretch' you're talking about through torqueing them up would be far more than the extra stretch 'load' placed on them from a steering input or bump. (in my opinion) so I doubt they would flinch.    - but again "not an engineer".      oh and I don't think stitch welding 7050 is a good idea, likely just weaken the material (from what I read)
×
×
  • Create New...