Jump to content
SAU Community

Recommended Posts

Hey all, so I just bought an R33 and its completely stock other than the exhaust system.. And the previous owner had installed an SBC Blitz boost controller..

Is there any benefit to having a boost controller if the cars basically stock? I've been driving with it off lately because I was thinking it would be no good running the car at higher boost than normal..

I've tried searching but couldn't find anything, cheers!

Link to comment
https://www.sau.com.au/forums/topic/432587-boost-controller-in-stock-r33/
Share on other sites

So it has Stock Side Mount Intercooler? Stock Airbox? Is the Exhaust Turbo back or Cat back?

Does it have an aftermarket boost gauge? What boost are you getting now?

If it's a stock turbo with stock ECU then you could go as high as 10psi but it would certainly be better with a more free flowing intercooler etc...

So it has Stock Side Mount Intercooler? Stock Airbox? Is the Exhaust Turbo back or Cat back?

Does it have an aftermarket boost gauge? What boost are you getting now?

If it's a stock turbo with stock ECU then you could go as high as 10psi but it would certainly be better with a more free flowing intercooler etc...

Yep stock side mount, stock air box, and I'm pretty sure its a cat back exhaust..

No aftermarket boost gauge and running it at 7psi..

pretty keen to start upgrading parts, but yea wanted to know if there is any benefit to having that boost controller and what boost I should run

Up to 10psi is in the Supposed safety zone for the stock turbo but also about all the ECU will handle before it gets all Rich & Retarded...

Get yourself a Just Jap Bellmouth Dump / Frontpipe, 3" Cat, some sort of Intercooler upgrade (either Frontmount or an R34 GTT sidemount) and get an R32 GTS-t 10psi Actuator. (or use the boost controller if you wish)

Have my luck turn the boost to 10-11psi give it a squirt up the street,

then blow the exhaust wheel into the cat

and turn the front wheel to dust

now the poor skyline is sitting there crying at me for a highmount but

bills and living expenses are more important :(

f**k my life yo

lol

It happens... Had a mate pull up in my driveway in his R34 GTT running 7psi on stock 34 turbo.

When he started it up again, there was a couple of clunking noises and suddenly it sounded like a supercharger and had no boost.

Exhaust wheel didn't break, it just fell off. :(

Luck of the draw doesnt even begin to describe the ceramic wheeled turbo failure scenario.

Im here in the UK atm and went to a GTROC meet. 2 stock R33 GTR's both on stock turbo's. 1 gets tracked several times a year. No problems..

I asked him if he was worried about the stock turbos or the oil pump tracking an old stock car like that. didn't seem to be.

I also had my '93 R33 GTST with stock turbo turned up to 15psi for 1.5-2 years. Never failed, just ended up upgrading the turbo to chase more power!

Go figure...

It is also best to leave it be n upgrade the turbo at the same time as the boost as there is also the chance the turbo can kill the motor when it lets go (turbine wheels bang on housings and send chunks of turbine wheel into the motor...).

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • When you crank your car, and hit it with a timing light, can you see a steady crank timing?
    • Oh, forgot to add, A few months ago I was getting mixture codes and the car was using crap loads of fuel. You could smell the unburned fuel in the exhaust, it was crazy strong. Economy was over 17.5 l/100 and usually around 19. I smoked the engine and found a leaky CCV hose which I replaced and then I replaced my two pre cat O2 sensors, I also replaced the MAF. This fixed my mixture codes and improved my exonomy but I'm still 14 - 15 l/100 when pottering about town so something is still amiss. Throttle response is much better and it has more pep but I'd like to know why it's still so thirsty (and I'm hoping that whatever it is gives me a bit more poke).    
    • Car is on factory injectors/z32 maf/ q45 throttle body/ z32 ecu with nistune 
    • Hello all, currently finishing up a rb25 swap into my s14. Having issues with starting, car has spark (confirmed by pulling a plug and watching it spark), has fuel(confirmed by checking pulse/voltage at injectors all spark plugs are soaked in fuel). Car cranks over and pops into the exhaust with a heavy fuel smell but no attempt to start or run, I have torn the timing cover off and triple confirmed timing, turned the CAS in multiple spots both directions, attempted to start with coolant temp and maf unplugged, checked my fuel lines and made sure they weren’t backwards, checked voltage at cas/injectors/coilpacks, made sure all the grounds in the harness are connected and added a few grounding straps (1 from chassis to block, 1 from chassis to head, and 1 from chassis to igniter chip) I am getting stumped here. As a last ditch effort I made a full grounding harness tonight that’s going to run from the battery and add an extra ground from the battery onto the coil pack harness/igniter chip/ intake manifold/ Wiring specialties harness ground/ and alternator. I’m hoping maybe the grounding harness will fix it here but posting here to see if anyone has any other ideas on what else I can check. My fuel pressure is unknown right gauge will be here tomorrow.  IMG_3206.mov
    • yeah I was shocked when I checked my spare OEM on and as below that's how they come from Nissan. (side interesting note new NEO gearbox and replacement park lack the brass bush on the tips and its just all alloy) unsure about damage to the box currently back at 1110 to be pulled down/inspected and selector fork replaced as he built it previously and given the never before seen failure on his billet forks he is replacing it under warranty. He said he has used always OEM the keyway tab without issue for years so it could be an unlucky coincidence. I did talk to him about the sharp corners and stress concentration too. Re: hard shifts i got 7+ years out of the OEM one and the fork itself failed not the keyway. so could be bad luck as I said or an age thing + heat cycles in box and during fabrication of billet?
×
×
  • Create New...