Jump to content
SAU Community

Recommended Posts

Hey guys- R34GTT running Precision 5558 and usual support mods- 18psi/286rwkw.

Got a timing light, disconnected TPS plugs, pulled no.1 coilpack off, ran a short spark plug wire from spark plug to coilpack (connected via a bolt) and clamped the timing light inductor to this wire.

Base Timing sits at around 13-13.5 degrees from eyesight, should I set this at 15degrees by rotating the CAS clockwise slightly? Do I do this with motor running or off and will this screw up my tune because I dont know if car was tuned at 13.5 or 15 degrees BTDC?

I have a missfire/power loss at WOT usually when hot and my off boost power seems low as well/ not as much torque. Have pulled off my z32 afm, cleaned it with brake cleaner n soldered the joints. Pulled off all plugs (coppers @0.8gap)n coils except no.4 and they all look in tip top shape/ no discoloration in plugs/fuel in cylinders etc. Coils are YJ less than 2 years old and I hope the farkers are ok. So Im hoping the missfire is because my timing is out a bit/ this likely?

Thanks for the help

Ok so came back after a bit of a spirited drive on such a hot day and checked timing again after a few mins cool down- now it was almost 15 degrees btdc- I would say 14.8-14.9 degrees btdc, so seems about alrite. Still had misfires on wot in the beginning but goes away..hoping its not the damn coilpacks as theyre still newish around 5-7000 kms and plugs are much much newer/looks new too. Afm cleaned/soldered n all- yet this farkin misfire rears its ugly head :/

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Welcome!  How long have you had it? And what colour is it?
    • "CAD" version 1.0 It will have a 15mm lip around the top for 6 × 5 or 6mm nutserts and fixtures (two on each of the three straight edges), and some pinch weld on any exposed edges, it has three mounting points, one of the power steering reservoir bolts, and two on the rad support, my 120mm hole saw will make short work of hole for the silicone joiner, with ample room for some pinch weld  I've also got enough Carbuilders "peel and stick" heat shield to cover the outside of it at the coolant expansion tank and on the engine side, as pictured, and internally on the lid and where the fuse box is, I've also got some thin, about 3mm, black 3M single sided sticky foam stuff that was left over after sealing some door drafts at home to help seal the lid As for the shape, it "sort of" matches the shape of the fuse box, so shouldn't look to "out of place" The lower area and hole for the intake will need pinch weld with a balloon on it to fully seal the hole and bottom of it, that will happen after it has been fabricated so I know exactly what size is required  Filter service has been trialed,  and so far it was a simple process  Just need to get some alloy, and then head into work to use the guillotine and break press in the workshop Hopefully it should be sorted in a week or two Guestimated outlay will be under a $50 for the stuff I don't have on hand (alloy, 6mm nutserts, the pinch weld, and wrinkle paint) Disclaimer: That's what the "voices in my head" are telling me how the filter box should end up getting done......lets see if they know what they are talking about  
    • Have been polishing up the trailer rims as they had been sitting in the shed for a few years and are really in need of some love. This was after a couple of passes with chrome polish - coming up quite well ✅ .
    • Welcome aboard! Is your Skyline auto or manual? I'm assuming manual. Does it have any mods done yet?
    • Hey mate, the brown and grey plugs would usually go to the TPS, brown one goes on the bottom connector and grey is the top but isn't used unless the car is auto, your TPS looks different to mine though I've got a series 2 engine.
×
×
  • Create New...