Jump to content
SAU Community

Recommended Posts

The R32- GTR is in my humble opinion one of the true 'apex technology' cars - the true highlight of its generation.....there was nothing more.....

The current Subi isn't at that level yet. If anything the R35 GTR approaches what I would expect from an 'apex' car using todays technology.

You feel that difference.......

Cheers

The Baron

Well put.....

Like a lot of things, we take stuff for granted until we get a chance to compare.

The only other car I really want to test drive is an E92 BMW M3.Unfortunately they are still serious money but an E46 manual (very rare) at $45K is more where I am likely to be but the V8 sounds fantastic.

I owned a Dakar Yellow E36 M3 for 3 years and loved it. It was an earlier version with the 3.0L 5 speed not the stupid SMG 6 speed which came out in the later 3.2L cars.

I'm not sure what I may end up with but I certainly know what i won't be owning and that's a STI.

Cheers,

Bob.

Well put.....

Like a lot of things, we take stuff for granted until we get a chance to compare.

The only other car I really want to test drive is an E92 BMW M3.Unfortunately they are still serious money but an E46 manual (very rare) at $45K is more where I am likely to be but the V8 sounds fantastic.

I owned a Dakar Yellow E36 M3 for 3 years and loved it. It was an earlier version with the 3.0L 5 speed not the stupid SMG 6 speed which came out in the later 3.2L cars.

I'm not sure what I may end up with but I certainly know what i won't be owning and that's a STI.

Cheers,

Bob.

I have heard the E36 BMW M3 really was a true drivers car. Really has a timeless shape as well. Any reason why you sold it off?

Btw, have you heard of any E36 M3 GTR's in the country? Would be really cool to own one of those...very rare as well I suspect

9ece1f938ba8aba7c3f661048749ff145314467e

I have heard the E36 BMW M3 really was a true drivers car. Really has a timeless shape as well. Any reason why you sold it off?

Btw, have you heard of any E36 M3 GTR's in the country? Would be really cool to own one of those...very rare as well I suspect

9ece1f938ba8aba7c3f661048749ff145314467e

I sold the M3 12 months after buying the ADM GT-R. I just struggled for room and the cost was a bit prohibitive.

What made things suck was 6 weeks after selling the car I got a promotion which would have allowed me to keep the car.

Anyway I looked around for a nice JDM R32 and ended up with one 3 months later.

I've toyed with selling it and there is a bit of interest here so I'm looking around for an alternative if it does sell.

Stupid part is I don't even know if I really want to sell it but that's another story!

The M3 GTR...... I think was only called a M3R for racing in Australia. BMW released 15 in the mid 1990's. All white and numbered. My mates race car is one and The Classic Throttle Shop in Sydney recently sold one.

Here - http://www.classicthrottleshop.com/soldcars.htm

Scroll down 18 rows but you can't enlarge the pic. Low mileage car..... Sold for about $60K.

Stunning car I had a good look at it before it sold but too much like my car for more than twice the price.

Here are some pics of my old M3.

post-78207-0-15011900-1383038082_thumb.jpg

post-78207-0-40250000-1383038086_thumb.jpg

post-78207-0-97382900-1383038090_thumb.jpg

post-78207-0-35941200-1383038095_thumb.jpg

post-78207-0-20716700-1383038100_thumb.jpg

E36 M3s are lovely. I had the evo with the getrag box. Awesome well rounded car.

26701_415568929080_6852816_n.jpg

I love E46s, never been in one though. Pity CSL is SMG only...

I drove another mates 2004 E46 M3 ....... Performance was great but it was a SMG. Hated that!

Good comparison Bob.

It's a nice read and know that a 20+ year old car can still put that smile on your face over the newer "technology" packed cars of today.

A manual E46 would be awesome but yes indeed a pain to find.

The newer E92 does sound amazing with the V8 but it does feel as if the car is doing most of the work for you.

That would probably be a deterring factor for you to differentiate between the two (not including price).

Of course, though, still an fantastic car!

Great little review, and one which mimics my sentiments accurately when I was looking at the WRX.

Following on with your comments on the E92/E90 M3, the prices have come down considerably, and with the announcement of the new Turbo M3 which is on its way, these will move even more I'd expect. So if this was a thought, it may still be a possibility.

Having said that however, I again was in a similar state of mind as you, and as much as the M3 was what I thought I wanted, and as wonderful as that V8 sounds, and as much as I'd just about convinced myself that that was what I'd buy, when it came to driving it, I never quite felt its bite matched its bark. I drove one on three different occasions and was left feeling the same way. Wonderful car, but there were other areas also which let it down, like the strangely notchy 6 speed and apparent lack of torque for such a motor.

Needless to say I couldn't settle on the M3, so I bought something else, but I've still kept the GTR, and if I'm honest, the new car is the closest thing I've driven which gives me a similar sensation to the raw, angry delivery of a GTR, and I think they're both wonderful. But I think an M3 is worth a drive if you're ever passing by a BMW dealer, because they are sublime in many other ways.

I went from a modded 05 sti, to a stock 99 2dr sti to a R32 v spec II. 05 had plenty of grunt (once modified) but felt heavy for what it was. 2 door was nice and super responsive. Definitely quicker than a gtr down low. Personally I prefer the gtr due to its presence (just look at those guards) and better steering. I also love the smoothness of the 6 after only having 4s.

I reckon a 22B vs some type of limited edition R34 would be an interesting comparison.

Edited by Cherry Racer
  • 3 weeks later...

My daughter owned this WRX for 9 months until we sold it to buy a MX-5.

I loved it and pleaded with her not to sell it but it was like talking to a brick wall.

Fortunately the MX-5 is a great car too and probably a bit more suited to a 21 year old.

If I didn't already have a fleet of cars I would have tried to find a way of keeping it but that simply wasn't possible.

The new car didn't feel much faster ( or that much better) than hers but was $60,000 more!

Cheers and thanks for the favourable comments about the review. It motivates me to keep finding interesting things to discuss.

Bob.

My other half has the bugeye sti, I love zippin it round the suburbs. My 34 has a gt35r and the lag is pretty painful after the sti

  • 3 weeks later...

Hi Guys........

Thought I'd just post an update.

I test drove a 2007 BMW M3 V8 today.

As you would expect it is a beautifully built car but the one thing that surprised me again was the outright performance.

Yes.... It's naturally quick but not in the way the GT-R is. The GT-R really has a WOW factor when pushed at 4500+ RPM's.

The M3 felt a bit lethargic. On paper it should be considerably quicker but it's not!

I don't think the car I drove was in perfect health so I'll make an allowance but once again, like with the STI I'm very comfortable is how good the R32 is.

Ok...... Next on the list to drive is a 2003-2007 Mercedes Benz SL55 AMG.

Cheers,

Bob.

post-78207-0-61271100-1386158503_thumb.jpg

post-78207-0-02664500-1386158519_thumb.jpg

post-78207-0-51975900-1386158527_thumb.jpg

post-78207-0-01011700-1386158535_thumb.jpg

very interesting read, thanks for sharing.

I recently got rid of my daily and now have my gtr up for sale and was looking into getting similar cars mentioned aboved and go back to one car.

At the top of my list is an evo X at this stage (sedan for daily is preferred for me). have you driven them at all? or they just dont interest you? Ive never driven one but would be interested in thoughts from gtr drivers that have??

Hi Guys........

Thought I'd just post an update.

I test drove a 2007 BMW M3 V8 today.

As you would expect it is a beautifully built car but the one thing that surprised me again was the outright performance.

Yes.... It's naturally quick but not in the way the GT-R is. The GT-R really has a WOW factor when pushed at 4500+ RPM's.

The M3 felt a bit lethargic. On paper it should be considerably quicker but it's not!

I don't think the car I drove was in perfect health so I'll make an allowance but once again, like with the STI I'm very comfortable is how good the R32 is.

Ok...... Next on the list to drive is a 2003-2007 Mercedes Benz SL55 AMG.

Cheers,

Bob.

* big_d sold his mp3 R34 GT-R V-Spec and went across to the SL55 AMG. He said he's quite happy and rarely misses the GT-R (although I don't think Derek went to the track in it)

* I'm not sure about the V8 M3, but when our eldest son Mark was alive and was a service advisor for BMW, he often came across M3s that had become sluggish.

> the BMW technicians warmed up the cars > checked the DMEs for fault codes and history > gave the cars a thorough thrashing (including NRL coach Ricky Stuart's) > performance was immediately better (according to the owners who asked, "what'd you do to it?")

* Me personally Anthony; for a contrasting performance car, I've been happy with the EVO 8MR (with Bilsteins). I mentioned that to Bob eh, at Casula one morning.

> it's chuckable

> after removing restrictions > replacements; like the lower FMIC pipe, hot turbo pipe & 3" Invidia exhaust

> much more seamless acceleration, bottom end power and midrange

Terry-49_zps033224bd.jpg

And it was a damn cheap Grade 4.5 (with full Japanese history) through JLM

Terry-51_zps87ddbc37.jpg[/u

Mitsubishi paint is frightfully thin at 120 microns tho'

Thanks Terry,

I do like the styling of the older evos a little better (7-9), but 08 model X's are now going for the same if not cheaper than 8MRs and IXs, and because its a daily i like the idea of it being only 5ish years old. then you have other added perks of the X including all the issues around imports, rust (i know this isnt exclusive to imports), odo readings, insurance, police hassels (potentially less in a X??), and generally a newer car with newer features, than can still be very fast and enjoyable aswell on the road and track, and as you said need very little mods to make them very fun...

if i had the money i would look closer at the V8 M3 sedan and C63 amg which are coming down in price...

ive found there isnt alot in the way of good performance sedans that are around 5 years old for or below 40-50k...

  • 4 weeks later...

Thanks Terry,

I do like the styling of the older evos a little better (7-9), but 08 model X's are now going for the same if not cheaper than 8MRs and IXs, and because its a daily i like the idea of it being only 5ish years old. then you have other added perks of the X including all the issues around imports, rust (i know this isnt exclusive to imports), odo readings, insurance, police hassels (potentially less in a X??), and generally a newer car with newer features, than can still be very fast and enjoyable aswell on the road and track, and as you said need very little mods to make them very fun...

if i had the money i would look closer at the V8 M3 sedan and C63 amg which are coming down in price...

ive found there isnt alot in the way of good performance sedans that are around 5 years old for or below 40-50k...

Nissan Skyline V36s sedans. 09 model onward updated front end 3.7 litre

I tell you one thing though with evo models 7-9 and the X, they handle like your driving a go kart. You can throw them so hard in the corners when you've upgraded the tyres, added some sways and suspension. But they have very short gear ratios and can run out of puff mid way 3rd gear.

Evo X has improved with it's handling performance no doubt but with the amount of after market availability for all evo's is just crazy.

I remember wanting to buy a FQ series evo many years ago but couldn't happen.

Edited by vspecIInur

Hey guys, thought I would put my 2 cents into this. I work at a subaru service centre as a technician (no im not an apprentice) and I test drive a lot of the new STi's I work on.

So first things first, yes they are very underwhelming in the performance side especially for how they look (big wing, big guards, big brembos and big wheels). The power comes on strong at first but just goes flat around the mid range of the RPM and it is very disappointing. Now these are the factory STis. I must admit I have a soft spot for them because I choose to work at subaru as I have a passion for them.

Now this is coming from someone that owns a 94 R32 GTR jdm and I will say, just with a flash tune and an exhaust, the STi is more exciting. Now the power comes on strong and stays pulling all the way to redline and you have torque at all RPM ranges. Now I only own a stock 32 and cant really say much for the modded scene, but as it stands now, I would rather be sitting in a lightly modded STi then a stock 32.

But with all that being said, im still not gonna ever own an STi. The raw presence of a GTR is legendary and unbeatable. I love my 32 to bits and will never sell it.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So this being my first contribution to the SAU forums, I'd like to present and show how I had to solve probably one of the most annoying fixes on any car I've owned: replacing a speedometer (or "speedo") sensor on my newly acquired Series 1 Stagea 260RS Autech Version. I'm simply documenting how I went about to fix this issue, and as I understand it is relatively rare to happen to this generation of cars, it is a gigantic PITA so I hope this helps serve as reference to anyone else who may encounter this issue. NOTE: Although I say this is meant for the 260RS, because the gearbox/drivetrain is shared with the R33 GTR with the 5-speed manual, the application should be exactly the same. Background So after driving my new-to-me Stagea for about 1500km, one night while driving home the speedometer and odometer suddenly stopped working. No clunking noise, no indication something was broken, the speedometer would just stop reading anything and the odometer stopped going up. This is a huge worry for me, because my car is relatively low mileage (only 45k km when purchased) so although I plan to own the car for a long time, a mismatched odometer reading would be hugely detrimental to resale should the day come to sell the car. Thankfully this only occurred a mile or two from home so it wasn't extremely significant. Also, the OCD part of me would be extremely irked if the numbers that showed on my dash doesn't match the actual ageing of the car. Diagnosing I had been in communication with the well renown GTR shop in the USA, U.P.garage up near University Point in Washington state. After some back and forth they said it could be one of two things: 1) The speedometer sensor that goes into the transfer case is broken 2) The actual cluster has a component that went kaput. They said this is common in older Nissan gauge clusters and that would indicate a rebuild is necessary. As I tried to figure out if it was problem #1, I resolved problem #2 by sending my cluster over to Relentless Motorsports in Dallas, TX, whom is local to me and does cluster and ECU rebuilds. He is a one man operation who meticulously replaces every chip, resistor, capacitor, and electronic component on the PCB's on a wide variety of classic and modern cars. His specialty is Lexus and Toyota, but he came highly recommended by Erik of U.P.garage since he does the rebuilds for them on GTR clusters.  For those that don't know, on R32 and R33 GTR gearboxes, the speedometer sensor is mounted in the transfer case and is purely an analog mini "generator" (opposite of an alternator essentially). Based on the speed the sensor spins it generates an AC sine wave voltage up to 5V, and sends that via two wires up to the cluster which then interprets it via the speedometer dial. The signal does NOT go to the ECU first, the wiring goes to the cluster first then the ECU after (or so I'm told).  Problems/Roadblocks I first removed the part from the car on the underside of the transfer case (drain your transfer case fluid/ATF first, guess who found out that the hard way?), and noted the transfer case fluid was EXTREMELY black, most likely never changed on my car. When attempting to turn the gears it felt extremely gritty, as if something was binding the shaft from rotating properly. I got absolutely no voltage reading out of the sensor no matter how fast I turned the shaft. After having to reflow the solder on my AFM sensors based on another SAU guide here, I attempted to disassemble the silicone seal on the back of the sensor to see what happened inside the sensor; turns out, it basically disintegrated itself. Wonderful. Not only had the electrical components destroyed themselves, the magnetic portion on what I thought was on the shaft also chipped and was broken. Solution So solution: find a spare part right? Wrong. Nissan has long discontinued the proper sensor part number 32702-21U19, and it is no longer obtainable either through Nissan NSA or Nissan Japan. I was SOL without proper speed or mileage readings unless I figured out a way to replace this sensor. After tons of Googling and searching on SAU, I found that there IS however a sensor that looks almost exactly like the R33/260RS one: a sensor meant for the R33/R34 GTT and GTS-T with the 5 speed manual. The part number was 25010-21U00, and the body, plug, and shaft all looked exactly the same. The gear was different at the end, but knowing the sensor's gear is held on with a circlip, I figured I could just order the part and swap the gears. Cue me ordering a new part from JustJap down in Kirrawee, NSW, then waiting almost 3 weeks for shipping and customs clearing. The part finally arrives and what did I find? The freaking shaft lengths don't match. $&%* I discussed with Erik how to proceed, and figuring that I basically destroyed the sensor trying to get the shaft out of the damaged sensor from my car. we deemed it too dangerous to try and attempt to swap shafts to the correct length. I had to find a local CNC machinist to help me cut and notch down the shaft. After tons of frantic calling on a Friday afternoon, I managed to get hold of someone and he said he'd be able to do it over half a week. I sent him photos and had him take measurements to match not only the correct length and notch fitment, but also a groove to machine out to hold the retentive circlip. And the end result? *chef's kiss* Perfect. Since I didn't have pliers with me when I picked up the items, I tested the old gear and circlip on. Perfect fit. After that it was simply swapping out the plug bracket to the new sensor, mount it on the transfer case, refill with ATF/Nissan Matic Fluid D, then test out function. Thankfully with the rebuilt cluster and the new sensor, both the speedometer and odometer and now working properly!   And there you have it. About 5-6 weeks of headaches wrapped up in a 15 minute photo essay. As I was told it is rare for sensors of this generation to die so dramatically, but you never know what could go wrong with a 25+ year old car. I HOPE that no one else has to go through this problem like I did, so with my take on a solution I hope it helps others who may encounter this issue in the future. For the TL;DR: 1) Sensor breaks. 2) Find a replacement GTT/GTS-T sensor. 3) Find a CNC machinist to have you cut it down to proper specs. 4) Reinstall then pray to the JDM gods.   Hope this guide/story helps anyone else encountering this problem!
    • So this being my first contribution to the SAU forums, I'd like to present and show how I had to solve probably one of the most annoying fixes on any car I've owned: replacing a speedometer (or "speedo") sensor on my newly acquired Series 1 Stagea 260RS Autech Version. I'm simply documenting how I went about to fix this issue, and as I understand it is relatively rare to happen to this generation of cars, it is a gigantic PITA so I hope this helps serve as reference to anyone else who may encounter this issue. NOTE: Although I say this is meant for the 260RS, because the gearbox/drivetrain is shared with the R33 GTR with the 5-speed manual, the application should be exactly the same. Background So after driving my new-to-me Stagea for about 1500km, one night while driving home the speedometer and odometer suddenly stopped working. No clunking noise, no indication something was broken, the speedometer would just stop reading anything and the odometer stopped going up. This is a huge worry for me, because my car is relatively low mileage (only 45k km when purchased) so although I plan to own the car for a long time, a mismatched odometer reading would be hugely detrimental to resale should the day come to sell the car. Thankfully this only occurred a mile or two from home so it wasn't extremely significant. Also, the OCD part of me would be extremely irked if the numbers that showed on my dash doesn't match the actual ageing of the car. Diagnosing I had been in communication with the well renown GTR shop in the USA, U.P.garage up near University Point in Washington state. After some back and forth they said it could be one of two things: 1) The speedometer sensor that goes into the transfer case is broken 2) The actual cluster has a component that went kaput. They said this is common in older Nissan gauge clusters and that would indicate a rebuild is necessary. As I tried to figure out if it was problem #1, I resolved problem #2 by sending my cluster over to Relentless Motorsports in Dallas, TX, whom is local to me and does cluster and ECU rebuilds. He is a one man operation who meticulously replaces every chip, resistor, capacitor, and electronic component on the PCB's on a wide variety of classic and modern cars. His specialty is Lexus and Toyota, but he came highly recommended by Erik of U.P.garage since he does the rebuilds for them on GTR clusters.  For those that don't know, on R32 and R33 GTR gearboxes, the speedometer sensor is mounted in the transfer case and is purely an analog mini "generator" (opposite of an alternator essentially). Based on the speed the sensor spins it generates an AC sine wave voltage up to 5V, and sends that via two wires up to the cluster which then interprets it via the speedometer dial. The signal does NOT go to the ECU first, the wiring goes to the cluster first then the ECU after (or so I'm told).  Problems/Roadblocks I first removed the part from the car on the underside of the transfer case (drain your transfer case fluid/ATF first, guess who found out that the hard way?), and noted the transfer case fluid was EXTREMELY black, most likely never changed on my car. When attempting to turn the gears it felt extremely gritty, as if shttps://imgur.com/6TQCG3xomething was binding the shaft from rotating properly. After having to reflow the solder on my AFM sensors based on another SAU guide here, I attempted to disassemble the silicone seal on the back of the sensor to see what happened inside the sensor; turns out, it basically disintegrated itself. Wonderful. Not only had the electrical components destroyed themselves, the magnetic portion on what I thought was on the shaft also chipped and was broken. Solution So solution: find a spare part right? Wrong. Nissan has long discontinued the proper sensor part number 32702-21U19, and it is no longer obtainable either through Nissan NSA or Nissan Japan. I was SOL without proper speed or mileage readings unless I figured out a way to replace this sensor. After tons of Googling and searching on SAU, I found that there IS however a sensor that looks almost exactly like the R33/260RS one: a sensor meant for the R33/R34 GTT and GTS-T with the 5 speed manual. The part number was 25010-21U00, and the body, plug, and shaft all looked exactly the same. The gear was different at the end, but knowing the sensor's gear is held on with a circlip, I figured I could just order the part and swap the gears. Cue me ordering a new part from JustJap down in Kirrawee, NSW, then waiting almost 3 weeks for shipping and customs clearing. The part finally arrives and what did I find? The freaking shaft lengths don't match. $&%* I discussed with Erik how to proceed, and figuring that I basically destroyed the sensor trying to get the shaft out of the damaged sensor from my car. we deemed it too dangerous to try and attempt to swap shafts to the correct length. I had to find a local CNC machinist to help me cut and notch down the shaft. After tons of frantic calling on a Friday afternoon, I managed to get hold of someone and he said he'd be able to do it over half a week. I sent him photos and had him take measurements to match not only the correct length and notch fitment, but also a groove to machine out to hold the retentive circlip. And the end result? *chef's kiss* Perfect. Since I didn't have pliers with me when I picked up the items, I tested the old gear and circlip on. Perfect fit. After that it was simply swapping out the plug bracket to the new sensor, mount it on the transfer case, refill with ATF/Nissan Matic Fluid D, then test out function. Thankfully with the rebuilt cluster and the new sensor, both the speedometer and odometer and now working properly!   And there you have it. About 5-6 weeks of headaches wrapped up in a 15 minute photo essay. As I was told it is rare for sensors of this generation to die so dramatically, but you never know what could go wrong with a 25+ year old car. I HOPE that no one else has to go through this problem like I did, so with my take on a solution I hope it helps others who may encounter this issue in the future. For the TL;DR: 1) Sensor breaks. 2) Find a replacement GTT/GTS-T sensor. 3) Find a CNC machinist to have you cut it down to proper specs. 4) Reinstall then pray to the JDM gods.   Hope this guide/story helps anyone else encountering this problem!
    • perhaps i should have mentioned, I plugged the unit in before i handed over to the electronics repair shop to see what damaged had been caused and the unit worked (ac controls, rear demister etc) bar the lights behind the lcd. i would assume that the diode was only to control lighting and didnt harm anything else i got the unit back from the electronics repair shop and all is well (to a point). The lights are back on and ac controls are working. im still paranoid as i beleive the repairer just put in any zener diode he could find and admitted asking chatgpt if its compatible   i do however have another issue... sometimes when i turn the ignition on, the climate control unit now goes through a diagnostics procedure which normally occurs when you disconnect and reconnect but this may be due to the below   to top everything off, and feel free to shoot me as im just about to do it myself anyway, while i was checking the newly repaired board by plugging in the climate control unit bare without the housing, i believe i may have shorted it on the headunit surround. Climate control unit still works but now the keyless entry doesnt work along with the dome light not turning on when you open the door. to add to this tricky situation, when you start the car and remove the key ( i have a turbo timer so car remains on) the keyless entry works. the dome light also works when you switch to the on position. fuses were checked and all ok ive deduced that the short somehow has messed with the smart entry control module as that is what controls the keyless entry and dome light on door opening   you guys wouldnt happen to have any experience with that topic lmao... im only laughing as its all i can do right now my self diagnosed adhd always gets me in a situation as i have no patience and want to get everything done in shortest amount of time as possible often ignoring crucial steps such as disconnecting battery when stuffing around with electronics or even placing a simple rag over the metallic headunit surround when placing a live pcb board on top of it   FML
    • Bit of a pity we don't have good images of the back/front of the PCB ~ that said, I found a YT vid of a teardown to replace dicky clock switches, and got enough of a glimpse to realize this PCB is the front-end to a connected to what I'll call PCBA, and as such this is all digital on this PCB..ergo, battery voltage probably doesn't make an appearance here ; that is, I'd expect them to do something on PCBA wrt power conditioning for the adjustment/display/switch PCB.... ....given what's transpired..ie; some permutation of 12vdc on a 5vdc with or without correct polarity...would explain why the zener said "no" and exploded. The transistor Q5 (M33) is likely to be a digital switching transistor...that is, package has builtin bias resistors to ensure it saturates as soon as base threshold voltage is reached (minimal rise/fall time)....and wrt the question 'what else could've fried?' ....well, I know there's an MCU on this board (display, I/O at a guess), and you hope they isolated it from this scenario...I got my crayons out, it looks a bit like this...   ...not a lot to see, or rather, everything you'd like to see disappears down a via to the other side...base drive for the transistor comes from somewhere else, what this transistor is switching is somewhere else...but the zener circuit is exclusive to all this ~ it's providing a set voltage (current limited by the 1K3 resistor R19)...and disappears somewhere else down the via I marked V out ; if the errant voltage 'jumped' the diode in the millisecond before it exploded, whatever that V out via feeds may have seen a spike... ....I'll just imagine that Q5 was switched off at the time, thus no damage should've been done....but whatever that zener feeds has to be checked... HTH
×
×
  • Create New...