Jump to content
SAU Community

Recommended Posts

In the Daily Telegraph today, watch the video too.

http://www.dailytelegraph.com.au/news/nsw/reading-the-riot-act-to-dodgy-car-dealers-over-odometer-tricks/story-fni0cx12-1226759295622

NSW Fair Trading and the Motor Traders' Association have warned the odometers of more and more vehicles - imports in particular - were being tampered with because, as things stand, "unscrupulous" car yards can get away with it.

But under a plan being developed by Fair Trading with Roads and Maritime Services (RMS), cars bound for Australia would have to be accompanied by papers showing their odometer reading at the time of deregistration in that country. This is not a requirement at the moment.

294847-e48e866a-4c42-11e3-95c1-9e9b6c573

John Rolfe in front of a questionable Toyota Supra on Parramatta Rd, Concord. Source: News Limited

Fair Trading is also exploring whether the Motor Dealers Act should be amended so car yards have to provide potential buyers with such information. Then dealers wouldn't be able to plead ignorance - which is enough to get them off the hook under current laws.

"Odometer tampering is a problem and it's on the increase," Fair Trading investigations director David Byrne said. The main source of imported used cars is Japan - about 5000 cars a year.

A web-based service which claims to be able to ascertain odometer readings on cars from Japan said 90 out of 100 odometers checked at the request of Australians were found to have been wound back.

In NSW there were 13 breaches in 2010-11 involving odometer tampering, 20 in 2011-12, 15 in 2012-13 and seven in less than four-and-a-half months this financial year, Fair Trading data shows.

Action is already on the way, with the penalty for tampering about to be doubled to $22,000.

Public Defender began investigating tampering after a tip from a victim, who pointed out a 2002 Toyota Supra. Auction papers he supplied - which I could not verify - said the car had done 91,170km when sold in Japan. This week I found the car on Sydney's Auto Alley. The odometer read 48,260km.

When it was put to the dealer, who cannot be named for legal reasons, that the odometer had been wound back, he said it wouldn't surprise him: "If that's happened it's happened on Japanese soil … I'm not the one who tampered with the odometer."

The dealer said the yard tried to limit its exposure to cars with tampered odometers but it was "rife" in Japan. There was no way of telling if a car had been driven further than its dashboard indicated.

Later the dealer rang to claim the auction papers I showed him may have been altered but he could not provide proof. Regardless, the Supra would be "removed from sale", he said.

A good step forward?

Edited by colourclassic
When it was put to the dealer, who cannot be named for legal reasons, that the odometer had been wound back, he said it wouldn't surprise him: "If that's happened it's happened on Japanese soil … I'm not the one who tampered with the odometer."

Right-o ;)

Well, when their stoopid enough to post Japanese agent shot videos with the original mileage visible, the car in their possession and the car arrives with 90k kms less, then it shouldn't be too hard.

However is that good enough for the law? I dunno.

You're able to request for the de-registration papers when the vehicle was in Japan.. it shows you the exact details, the KMs, etc...

I like how dealers always blame the Japanese winding down KMs, etc.. they're a very honest society, they wouldn't do any of that shit. Even when the tsunami took out a town, ATMs were destroy and money was floating about.. no one looted, no one picked up a single note floating about. So what says they want to even wind their KMs back?

It's all done here before compliance.

You're able to request for the de-registration papers when the vehicle was in Japan.. it shows you the exact details, the KMs, etc...

I like how dealers always blame the Japanese winding down KMs, etc.. they're a very honest society, they wouldn't do any of that shit. Even when the tsunami took out a town, ATMs were destroy and money was floating about.. no one looted, no one picked up a single note floating about. So what says they want to even wind their KMs back?

It's all done here before compliance.

Interesting idea, and I agree with you about Japanese culture. However I believe there are a lot of people of a certain ethnic group that is not Japanese that are a big part of the car business. I've seen details of it in the past, however can't remember where I saw it.

so those dealers blaming the Japanese docks can go get fuarked...

The cars in Japan are all auctioned with usually 100 000+ kms on them some how they end up here with like 1/3 of the kms. I've seen it with my own eyes, same car in an auction site, de-registration papers, then blame at XYZ dealer in Parramatta Road with 1/3 the kms.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
    • The video for the servicing and fuel filter change can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44 One of the main jobs I wanted to do before the car officially went on the road, was to remove the awful looking blue silicone hoses. There's nothing wrong with having coloured silicone hoses, but I realise as I'm getting older I prefer monotone engine bays with a splash of colour on the engine cover(s). I cover this in a lot more detail in the Youtube video, so unfortunately there's limited photos of the process. The intercooler, upper radiator, boost vacuum and upper breather hoses were all changed to black silicone with mikalor clamps. The only blue left is a blanking cap at the back of the inlet manifold and the GReddy pulleys (which will be replaced for stock when the cambelt gets replaced) While the intercooler pipes were off I gave them a quick clean/polish too A before photo I do have a replacement air filter on its way. Fuse box covers were painted blue, they're now satin black Another job on the list while the bumper was off, is to add some mesh https://live.staticflickr.com/65535/54737966256_99b28bfa30_c.jpg[/img] I was hoping to use some thin wire to secure it, but it seems I've misplaced it and the wire I had was too thick to twist easily. I ended up using cable ties for the time being https://live.staticflickr.com/65535/54737131882_c2b7989dcc_c.jpg[/img] Was pleasant to see this https://live.staticflickr.com/65535/54737131627_8b2aab13b3_c.jpg[/img] The last thing to do was to fix the front grill and re-mesh that to match but I ran out of time The Youtube video can be seen here: https://www.youtube.com/watch?v=R4FsF6tgizE&t=23s
    • Hi all,I already introduced myself in the Victoria section, but only saw this section now lol XD New to forums and new to skylines. Hoping to buy my new skyline within October
×
×
  • Create New...