Jump to content
SAU Community

Recommended Posts

Can anyone get hold of one of these. I am in the UK and cant find anyone that does them!

I need it to fit to my titanium exhaust as I have just fitted a single turbo and had a 4" downpipe made up thinking my exhaust was 4" all the way through but it expands to 4" from 3.5"

Any help would be massively appreciated as i am now stuck with a car I cant use :(

Link to comment
https://www.sau.com.au/forums/topic/435011-need-a-4-titanium-v-band-flange/
Share on other sites

Or you could get a stainless clamp and have some rings laser cut from titanium plate. Then weld them on one at a time using a stainless flange to keep it straight while welding, and push the pipe through a tiny bit so the holes centre and line up.

Or you could get a stainless clamp and have some rings laser cut from titanium plate. Then weld them on one at a time using a stainless flange to keep it straight while welding, and push the pipe through a tiny bit so the holes centre and line up.

Interesting idea but the problem is i have to take it to a shop to do it and not sure if they would do something like that or not...

Can you find a machinist to make you one, the other half of what you have now?

I dont actually have a flange on the downpipe i was going to get a stainless steel 2 bolt flange made up and get that welded to the downpipe but then when i went to get a drawing of my exhaust flange made up i saw it was actually a 3.5" flange which expands into 4"

My exhaust is a custom made in japan job as well from an Auto Select car.

If you can find some stainless that slides nicely into the 4 inch Ti and slot it then clamp, it will be fine. Motorbikes use slip fittings like that all the time. Probably not the best outcome for such an expensive system though.

I guess you want to ditch the 3.5 inch section? Probably best you measure the Ti also, as the Japanese like to use metric pipe usually.

If you can find some stainless that slides nicely into the 4 inch Ti and slot it then clamp, it will be fine. Motorbikes use slip fittings like that all the time. Probably not the best outcome for such an expensive system though.

I guess you want to ditch the 3.5 inch section? Probably best you measure the Ti also, as the Japanese like to use metric pipe usually.

That is an idea, but would prefer it to be bolted or v-band. Even a 2 bolt flange would do me or a 4 bolt as long as i can get a stainless one too!

The guys who fabricated my downpipe built it on their R33 as they are quite far away from me, i sent them my turbo and manifold and they bolted it up to their car and did the work. They made the downpipe a bit longer just in case as they didnt have my exhaust. I think there is enough on there to cut the 3.5" section off my Ti exhaust and still get it bolted up...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You just need to remove the compressor housing, not the entire turbo. I would not be drilling and tapping anything with the housing still on anyways. 
    • So, I put my boat on a boat. First of all, I'm going to come out and say it. Why is Tasmania not considered a holy goal, an apex that all road-legal modified cars go to, to experience? This place is an absolute wonderland of titanic proportions. If people are already getting club runs for once in a lifetime 30 person cruises to Tassy then I've never seemed to see it. It is like someone replaced the entire place with an idyllic wonderland for cars, and all of the people living there with paid actors who are kind, humble, and friendly. Dear god. After doing a lap of almost all of the place I've found that it's a great way to find out all of the little things that the car isn't doing quite right and a great way to figure it all out. All in all, I drove for 4 hours a day for a week and nothing broke. I didn't even need to open the engine bay. This is by all means a great success, but it has left me with a list of things to potentially address. I also now have a 3D printed wheel fitment tool which annoyingly hasn't got any threads in it to actually assemble it. I might be able to tape it together to check the sizing I actually want to use, but it'll likely involving pulling the shocks out to properly measure travel at least at the front, and probably raise the car while I'm at it, at least in the rear. I scraped on quite a few things and I'm not sure how else to go about it. I was taking anything with a bump at what felt like 89 degree angles. And address those 10 other tasks. And wash the car. God damn it is dirty. And somehow, the weather was perfect the entire time - And because I was on the top of Mt Wellington it turns out it was very much about to freeze up there. I did something I typically never do and took some photos up there in what must have been -10 and the foggy felt like suspended ice, rather than mere fog. If you own a car in Australia, you owe it to yourself to do it.
    • Damn that was hilarious, and a bit embarrassing for skylines in general 😂 vintage car life ey. That R33 really stomped. Pretty entertaining stuff
    • Hi, I have a r32 gtr transmission. Does any of you guys have an idea how much power it will hold with the billet center plate and stock gearset? At what power level and use did yours brake with or without billet plate? Thanks, Oystein Lovik
    • Saw this replica police car based on a Mitsubishi Starion XX parked next to a 'police box' (it's literally a box) in Hirohata, Himeji City in Hyogo prefecture the other day. It's owned by Morii-san who is a local Mitsubishi Starion enthusiast. According to a local radio station blog post, he always wanted to make a police car himself based on ones he saw in his favourite Manga comics.  As it's illegal to modify a car to look like a police car and drive on the road, Morii-san tried many times to get permission from Aboshi police station headquarters nearby. They refused initially by after they got tired of that they granted him permission. However, the car can only be displayed on private property and obviously can't be registered as long as the police livery is present. The car was completed at a cost of 1.5 million yen (US$ 10,000) in addition to the car cost. A location was chosen outside Hirohata Police box where the car can easily been seen from the street. Morii-san has two other Starion road cars, both widebody GSR-VRs.
×
×
  • Create New...