Jump to content
SAU Community

Recommended Posts

01 V35 Sedan - mums car.

After parking in the (hot) sun for a while, the dash instruments don't work, nor do the dash lights.

Temp display works - but air con power / sound system power - nothing works.

Then everything starts to work after a while when it cools down.

As you can imagine, this gets annoying... :angry:

Any ideas?

Edited by 10 4

Given it affects AC and stereo control as well, I'd say you have a dry joint somewhere in the AV system, starting with the AC+instrumentation amp module. That said, I'm not familiar with the V35 as much as I am with the V36 but that's where I would start.

Get your hands on the factory service manual for it and trace the schematic back from the dash cluster (or combination meter, as it's called in the manual). See which module it plugs into and then take out that module for an inspection. Dry joints aren't all that obvious to pick up on without some serious magnification but if you're good with a decent soldering iron (i.e. a proper temperature controlled unit), if you pick the logical points where it wires into and resolder the joints with just a little touch of fresh solder, that would be your starting point. Should it still exhibit the same issues, keep working your way through the circuit, reflowing all joints leading back until it comes alive.

Also, check for any capacitors which may have dried out. It's pretty obvious, even with the SMD types, where you notice the can having bulged out at the top and/or sides. Pay particular attention to any electrolytics which may have been also heatshrinked as well. Carefully cut the heatshrink off and inspect accordingly. Be sure to replace them with not only the same value capacitance but also the same minimum working voltage ("WV"). You can go to a higher WV rating if it physically fits but don't go lower. Also check for any leaked electrolyte on the board, which can result in corrosion of the copper traces. Be sure you clean it with some circuit board cleaner and double check it's all gone by applying a little heat from your soldering iron and wafting it for any unusually pungent smells. If you still smell something pungent, it's not entirely cleaned up.

Given the problem is thermally related, I'd say the cause is a fairly simple one, hence why I've mentioned dry joints first. The caps may not really be the result of a thermal issue but they may be possibly storing enough of a charge eventually to power up so while you think it's because it has cooled down, the reality may be that it just had enough time to eventually charge up.

The less likely cause is a bad semiconductor, typically a transistor or two supplying power to all those devices. In which case, diagnosing a bad one while in circuit isn't as easy, particularly when dealing with a thermal issue. That takes a can of good freeze spray (such as Electrolube's MCF400) and hitting the suspected components until one of them gives you the expected result.

Unless it's a common fault mentioned on one of the G35 forums in the US or something, you'll be hunting for the culprit but you'll feel very satisfied for having fixed it. Best of luck and let us know what you find. You might save someone else's bacon one day.

  • 5 months later...

Old problem still not fixed - no one has had same issue as far as I can tell....

New issue today: THUD/CLUNK into drive / reverse and when put into tiptronic mode, its stuck in 4th gear. Restart car = same issue. AT check light comes on then goes off so no issue there. Also speedo works, fuel gauge works, tacho and temp gauge does not work.

Is not driveable atm.

FFS.

Edited by 10 4

Just because the AT light goes off, doesn't mean there is no fault.

The auto is in limp mode, you need to get a Consult unit on it to find out the code. Wish I could help but it would be a long drive.

Every time you re-start the car it returns to normal operation, as long as the reason for the fault is gone.

Sounds like an overheated transmission fluid fault. You may want to get it looked at sooner rather than later, it's not like we are in summer anymore, so if it's overheating you may have other issues.

I like the theory.. But the trans thud / stuck in 4th along with 1 side of dash working.. only happened once when it was ~ 8deg outside in the morning. I started the car and that was it. Parked it, restarted same issue. Left it a day then all was well...

It's not a theory, my trans has been in limp mode many times. It gets locked in 4th when it overheats/faults.

I would say you had an issue with the temp sensors in the gearbox, but only a Consult unit can read it properly to prove the fault.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
    • I got adjustable after market rear camber arm to replace the stock one's because got sick of having to buy new rear tyres every few months. Can anyone please let me know what the best adjustment length would be. I don't have the old ones anymore to get measurements. I'm guessing the stock measurement minus a few mm would do it. Please any help on replacing them would be fantastic I've watched the YouTube clips but no-one talks about how long to set the camber arm to.
    • Heh. I copied the link to the video direct, instead of the thread I mentioned. But the video is the main value content anyway. Otherwise, yes, in Europe, surely you'd be expected to buy local. Being whichever flavour of Michelin, Continental or Pirelli suits your usage model.
×
×
  • Create New...