Jump to content
SAU Community

Fs [Syd]: Genuine Recaro Sr3 Bucket Seat With Bolt-In Low Rails For R32/r33/r34 Gts-T & Gt-R Minus Gt-T

Dose Pipe Sutututu
 Share

Recommended Posts

Dose Pipe Sutututu Grand Master

Dose Pipe Sutututu

Posted
Posted

Harro,

I has for sale seat. It's a black GENUINE Recaro SR3 bucket seat with a DRIVER SIDE bolt-in rail. Not sure of rail brand but it's not some cheap shit hack job. I'm guessing it's a Cluster rail or even a RECARO rail. Why bother installing some fake seat, get the real deal :)

It's a little worn, but if you know of someone to reupholsters the wings you're winning!

There were a few tears and holes but I've stitched up them up etc.. however the middle section is still good.

Foam wise, the left wing and the centre still is in great condition, just the right wing has collapsed like most of them have (you can get a replacement off eBay)

Great seat, good price if you don't give a shit too much on looks and just want a seat to hold you firmly on the track/drags/touge/skids/hoon/stance/hellaflush/poser/jdmst/stupidhomocarmeets etc..

Price: $350 (consider that rail alone is $200+ used on eBay)

Location: Canley Vale, NSW, 2166

Contact: Here OR PM

* Photos will be up tonight

Dose Pipe Sutututu Grand Master

Dose Pipe Sutututu

Posted
  • Author
Posted

fuark bucket seat

just get it reupholstered if you're bothered for about $200, that makes it $500 for a mint recaro seat & rail

  • 2 weeks later...
Dose Pipe Sutututu Grand Master

Dose Pipe Sutututu

Posted
  • Author
Posted

WILL SPLIT RAIL & SEAT

SEAT $200

RAIL $150 (with plates to bolt to a RECARO SEAT)

  • 2 weeks later...
xALmoN Grand Master

xALmoN

Posted
Posted (edited)

2 hundy? hao mut to send to melbourne 3125?

yeah no need rails, me has bride railz.

Edited by xALmoN
Dose Pipe Sutututu Grand Master

Dose Pipe Sutututu

Posted
  • Author
Posted

too muk man, seat is the bic wun lol

Unless you can get cheap courier? I'm happy to sell it for $200 + postage

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • JC71
      98 R34GTT 4k engine stumble

      By JC71 · Posted

      neither stumble or cut really seem to be an appropriate term....hard to explain its like a rev limiter but at 4k, but it violently shakes engine and entire vehicle as the rpms will not rise over 4k, even with slow acceleration. as soon as it hits 4k, it sounds like entire spark is lost entirely. plugs were 1.1 which I used as such, but later put in new plugs gapped down to .8 changed back after issue arose when I replaced the coils, still does it with either plug gap...damn and it was all running so good.
    • TurboTapin
      Why am I hitting a power wall with my stroked RB25?

      By TurboTapin · Posted

      Oh how times have changed! I actually lean it out relative to my water/methanol injector duty cycle. The methanol adds a lot of fueling and you can then lean it out even more due to reduced knock. 
    • Dose Pipe Sutututu
      Why am I hitting a power wall with my stroked RB25?

      By Dose Pipe Sutututu · Posted

      Yeah my thoughts are the same, a well thought out WMI setup, would be slightly ahead of just straight E85 and you're also chemically intercooling the charged air, dropping it even further. This is why you need to add so much more fuel as soon as you spray. I remember someone taking me through their set up before (Dennis, has a R33, lives around Cabramatta - no idea if he's still around on this forum). He would target AFR 10:1 on 98, then as WMI ramped on, AFR would lean back up to 11:1. Amazingly, he did this all through his PowerFC, a relay to cut power to his EBC solenoid if there was not enough line pressure on his WMI kit. And of course, if there wasn't any boost made above gate pressure, you wouldn't be accessing the load cells with heaps of timing for WMI. One downside to that rudimentary setup, once the WMI came on, the EBC would unleash the dragon, and of course all the timing. Tyres would fry lol.
    • MBS206
      RB25DET with solid lifters - which cams ?

      By MBS206 · Posted

      Shimmed or shimless, still solid, no hydraulic pump up stuff.
    • MBS206
      NC MX5

      By MBS206 · Posted

      They have said food will be limited. Mainly meat pies and sausage rolls from memory. But they have a coffee van!
×
×
  • Create New...