Jump to content
SAU Community

Vic - Wrecking R33 Gtst S1.5 - Black

Steg33
 Share

Recommended Posts

Steg33 Community Regular

Steg33

Posted
  • Author
Posted

G'day,

Am interested in rear hubs with immediate brake cables.

How much with postage to Canberra.

Thanks.

FYI, I think you inbox may be full, will not let me send PM to you.

Hey mate,

Sorry, the hubs and handbrake cables are sold pending pickup. If anything changes I'll let you know.

Thanks for the heads up on the inbox as well! It's now clear for anyone trying to send pm's.

Steg33 Community Regular

Steg33

Posted
  • Author
Posted

Hey mate still got the centre console/handbrake boot?

Also what are you doing with the shell of the car?

Hey mate,

I've still got the center consol/handbrake boot.

The shell im still looking at selling once ive got a few more things out of it. Open to offers depending whats wanted left it it. At the moment there's fuel and brake likes, instrument panel, carpet, garnish trim etc...

  • 2 weeks later...
  • 3 weeks later...
Steg33 Community Regular

Steg33

Posted
  • Author
Posted

Just back from holidays so apologies for the delayed replies.

- Front chassis harness is still available with fuse box.

- Confetti recaro seat is sold BUT other recaro is still available and I'll even take $150 just to move it.

- All brake callipers are SOLD.

Steg33 Community Regular

Steg33

Posted
  • Author
Posted

How much?

I'm after $150 for the chassis harness with the fuse/relay box included. Picture below to confirm we're talking about the same harness (circled in red)?

It's in great condition except for 2 wires on the dash side that need re-soldering due to the alarm being taken out.

post-7819-0-39690600-1389601151_thumb.jpg

post-7819-0-22186800-1389601234_thumb.jpg

Steg33 Community Regular

Steg33

Posted
  • Author
Posted

Odd question, which side does your brake master cylinder cable connect to? Need on that connects in the driver side..... Just the connector and maybe 4 inches of its cable

Cable??

There aren't any cables as such on the driver's side of the firewall. There is only an adjustable joining rod from the pedal to the cylinder.

Is that what you're after?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • JC71
      98 R34GTT 4k engine stumble

      By JC71 · Posted

      neither stumble or cut really seem to be an appropriate term....hard to explain its like a rev limiter but at 4k, but it violently shakes engine and entire vehicle as the rpms will not rise over 4k, even with slow acceleration. as soon as it hits 4k, it sounds like entire spark is lost entirely. plugs were 1.1 which I used as such, but later put in new plugs gapped down to .8 changed back after issue arose when I replaced the coils, still does it with either plug gap...damn and it was all running so good.
    • TurboTapin
      Why am I hitting a power wall with my stroked RB25?

      By TurboTapin · Posted

      Oh how times have changed! I actually lean it out relative to my water/methanol injector duty cycle. The methanol adds a lot of fueling and you can then lean it out even more due to reduced knock. 
    • Dose Pipe Sutututu
      Why am I hitting a power wall with my stroked RB25?

      By Dose Pipe Sutututu · Posted

      Yeah my thoughts are the same, a well thought out WMI setup, would be slightly ahead of just straight E85 and you're also chemically intercooling the charged air, dropping it even further. This is why you need to add so much more fuel as soon as you spray. I remember someone taking me through their set up before (Dennis, has a R33, lives around Cabramatta - no idea if he's still around on this forum). He would target AFR 10:1 on 98, then as WMI ramped on, AFR would lean back up to 11:1. Amazingly, he did this all through his PowerFC, a relay to cut power to his EBC solenoid if there was not enough line pressure on his WMI kit. And of course, if there wasn't any boost made above gate pressure, you wouldn't be accessing the load cells with heaps of timing for WMI. One downside to that rudimentary setup, once the WMI came on, the EBC would unleash the dragon, and of course all the timing. Tyres would fry lol.
    • MBS206
      RB25DET with solid lifters - which cams ?

      By MBS206 · Posted

      Shimmed or shimless, still solid, no hydraulic pump up stuff.
    • MBS206
      NC MX5

      By MBS206 · Posted

      They have said food will be limited. Mainly meat pies and sausage rolls from memory. But they have a coffee van!
×
×
  • Create New...