Jump to content
SAU Community

Recommended Posts

Hello

I have just finished pulling down my GTR motor, after suffering what a few others have, and found that the 1st and 2nd big end bearings are shot. The damage was severe enough to have scored the crank beyond repair. This was caused by a track day at Wakefield were I only completed 5 laps before stopping. During this time the oil pressure and temperature was good.

My first question is: how does this occur? I assume from reading other posts that the motor experiences surging and also pools oil in the back of the head. This causes the bearings to temporarily be without oil and start to bind? Would the five laps have been enough to turn the bearings into paper thin strips? or had the bearings already had some damage?

the second question is: how do you stop this from occuring again? I have seen products like the Jun sump baffle kit, and the Grex sump extension kit with baffle. Also, I have read about blocking the oil from the head via head gaskets?

any help appreciated as I do not want to rebuild the engine only to have it go the next time I am on the track again.

Cheers.

Link to comment
https://www.sau.com.au/forums/topic/43555-rb26dett-spun-bearings/
Share on other sites

Hi Shoey, I would never ever take a GTR to the circuit with a standard sump and without an oil cooler. Oil surge is always very close. The more power you have or the better the suspension and tyres, the closer it is to oil starvation. It builds up in the head due to constant high rpm, the engine uses a bit, the oil gets over heated and it runs away from the oil pickup around the corners due to g forces.

We do the following;

*Add wings, one way doors and baffles to the sump

*Use an oil cooler with remote filter

*Increase the diameter of the oil return galleries in the head and block

*Fit an external oil return direct into the sump from the rear of the cylinder head

*Use hi viscosity oil (Castrol Formual R Synthetic 10W60 in our case)

Our race team fabricator makes ours as I am not happy with the "off the shelf" products. Performance Metalcraft do a really good custom sump for GTR's. :aroused: That would be my choice for "retail" product, there are probably others around.

As for you questions about 5 laps being enough, I have seen a GTR chuck a rod out of the side of the block in 3 laps. You were lucky.

Hope that helps :wavey:

Ive noticed alot lately when being around GTRs that they have a problem with high oil temps, why is this sk? Why doesnt RB25DET have the same problem? Minus the extra turbo ofcourse :)

Let's see, I could start with RB25DET's have one ball bearing, watercooled turbo and a GTR has two plain bearing, oil cooled turbos. Then I would follow it with GTR's have a hot diff bolted to the side of the sump and a drive shaft running through it. I would finish up with GTR's make more power (standard) so they have to produce more heat.

I am sure other could add to the list. :P

yes rb25 does have the same problem, but it doesn't get exacerbate by the existent of a 4wd system as is on the gtr. a gtst would swap ends, if u pushed it hard enuff, it only becomes a problem when you run semi slick,

i have heard the genuine nissan clearances are to tight from factory .7thou on the rods and .9 thou mains i think is factory clearances, i was build a toght motor when my tuner pointed out he think the clearances are to tight for big HP standard is ok but for big HP he recommended 1.2 for the rods and 1.5 for the mains , he said make sure its blue printed and machined correctly by reputable machine shop, he said this in turn will creat more of an oil surface film and decrease the chances of metal to metal if used with full synthetic oil.

please correct me if anybody has been told differant this is just 1 person view point not fact

has anybody heard this also ?

Hi Shoey, I would never ever take a GTR to the circuit with a standard sump and without an oil cooler.  Oil surge is always very close.  

Now in hindsight that seems like great advice :P

The new engine will have Trust Sump extension and baffles, big oil cooler and restrictor in the oil gallery.

What I can’t understand is how the car was built with so much techno detail ie. attessa, twin afm’s, hex throttle bodies and yet on the track with a few laps a lot of them die a miserable death.

Surely the car was flogged senseless around a track before sold to the public? We aren’t talking about a chook cooker a to b grocery getter here.

Strange….

Yes, I did not think that a car like the GTR would suffer too much from track days. I did actually fit a remote oil filler and changed oil before going. Thanks for the advice. I think I will look into the custom sump idea as I would like ot return to the track without having the large repair bill.

Do your self a favour and don`t go out on the track untill you have sump baffles, extra capacity etc. My GTR shot a rod out the side of the block in only two laps of a short circuit. It already had an oil cooler and remote filter but on semi slick tyres it took no time at all to cause a very expensive failure. It`s not worth the risk.

Cheers, Dror

What I can’t understand is how the car was built with so much techno detail ie. attessa, twin afm’s, hex throttle bodies and yet on the track with a few laps a lot of them die a miserable death.

Surely the car was flogged senseless around a track before sold to the public?

would it be fair to say that most examples of GTR's on the track are modified to a certain extent?

running more boost/exhaust and sometimes ECU to be a making a lot more power...

hence pushing the engineering a bit. Not that GTR's are not over engineered but remember the full track variants would have all the above mentiond 'additional mods' like baffling etc etc

As SK said, suspension and/or tyres makes a big difference to the whole equation too. Even on a stock car i would imagine

My car was running an exhaust, had the boost restrictor removed and had adjustable cams gears. I think it produced 211kw at 4 wheels at Croydons. Therefore a very mildly modified example. My suspension was konis with King springs but I was getting a lot of slide due to cheap Khumo tyres. I think the excessive slide would also have contributed to oil movement.

SydneyKid, I have one more question: You talk about enlarging the oil chambers returning to the sump.  Do you also recommend putting in a oil restrictor for the feeds to the head?  Or is this not necessary because of the larger returns and extra external return oil feed?

RB26DETT's have an oil restrictor in the top of the block standard. Make sure if it is removed for decking, that it is replaced.

How much would it cost for a baffle sump + install (in an R33GTR) ?

Does the engine have to come out?

You can get Trust sumps and oil cooler, RB26DETT on here has them on his GTR that is for sale

Dont know how much they are, but SK said local/custom ones seem to be better than jap brands

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The other problem was one of those "oh shit we are going to die moments". Basically the high spec Q50s have a full electric steering rack, and the povo ones had a regular hydraulic rack with an electric pump.  So couple of laps into session 5 as I came into turn 2 (big run off now, happily), the dash turned into a christmas tree and the steering became super heavy and I went well off. I assumed it was a tyre failure so limped to the pits, but everything was OK. But....the master warning light was still on so I checked the DTCs and saw – C13E6 “Heat Protection”. Yes, that bloody steering rack computer sitting where the oil cooler should be has its own sensors and error logic, and decided I was using the steering wheel too much. I really appreciated the helpful information in the manual (my bold) POSSIBLE CAUSE • Continuing the overloading steering (Sports driving in the circuit etc,) “DATA MONITOR” >> “C/M TEMPERATURE”. The rise of steering force motor internal temperature caused the protection function to operate. This is not a system malfunction. INSPECTION END So, basically the electric motor in the steering rack got to 150c, and it decided to shut down without warning for my safety. Didn't feel safe. Short term I'll see if I can duct some air to that motor (the engine bay is sealed pretty tight). Long term, depending on how often this happens, I'll look into swapping the povo spec electric/hydraulic rack in. While the rack should be fine the power supply to the pump will be a pain and might be best to deal with it when I add a PDM.
    • And finally, 2 problems I really need to sort.  Firstly as Matt said the auto trans is not happy as it gets hot - I couldn't log the temps but the gauge showed 90o. On the first day I took it out back in Feb, because the coolant was getting hot I never got to any auto trans issues; but on this day by late session 3 and then really clearly in 4 and 5 as it got hotter it just would not shift up. You can hear the issue really clearly at 12:55 and 16:20 on the vid. So the good news is, literally this week Ecutek finally released tuning for the jatco 7 speed. I'll have a chat to Racebox and see what they can do electrically to keep it cooler and to get the gears, if anything. That will likely take some R&D and can only really happen on track as it never gets even warm with road use. I've also picked up some eye wateringly expensive Redline D6 ATF to try, it had the highest viscosity I could find at 100o so we will see if that helps (just waiting for some oil pan gaskets so I can change it properly). If neither of those work I need to remove the coolant/trans interwarmer and the radiator cooler and go to an external cooler....somewhere.....(goodbye washer reservoir?), and if that fails give up on this mad idea and wait for Nissan to release the manual 400R
    • So, what else.... Power. I don't know what it is making because I haven't done a post tune dyno run yet; I will when I get a chance. It was 240rwkw dead stock. Conclusion from the day....it does not need a single kw more until I sort some other stuff. It comes on so hard that I could hear the twin N1 turbos on the R32 crying, and I just can't use what it has around a tight track with the current setup. Brakes. They are perfect. Hit them hard all day and they never felt like having an issue; you can see in the video we were making ground on much lighter cars on better tyres under brakes. They are standard (red sport) calipers, standard size discs in DBA5000 2 piece, Winmax pads and Motul RBF600 fluid, all from Matty at Racebrakes Sydney. Keeping in mind the car is more powerful than my R32 and weighs 1680, he clearly knows his shit. Suspension. This is one of the first areas I need to change. It has electronically controlled dampers from factory, but everything is just way too soft for track work even on the hardest setting (it is nice when hustling on country roads though). In particular it rolls into oversteer mid corner and pitches too much under hard braking so it becomes unstable eg in the turn 1 kink I need to brake early, turn through the kink then brake again so I don't pirouette like an AE86. I need to get some decent shocks with matched springs and sway bars ASAP, even if it is just a v1 setup until I work out a proper race/rally setup later. Tyres. I am running Yoko A052 in 235/45/18 all round, because that was what I could get in approximately the right height on wheels I had in the shed (Rays/Nismo 18x8 off the old Leaf actually!). As track tyres they are pretty poor; I note GTSBoy recently posted a porker comparo video including them where they were about the same as AD09.....that is nothing like a top line track tyre. I'll start getting that sorted but realistically I should get proper sized wheels first (likely 9.5 +38 front and 11 +55 at the rear, so a custom order, and I can't rotate them like the R32), then work out what the best tyre option is. BTW on that, Targa Tas had gone to road tyres instead of semi slicks now so that is a whole other world of choices to sort. Diff. This is the other thing that urgently needs to be addressed. It left massive 1s out of the fish hook all day, even when I was trying not too (you can also hear it reving on the video, and see the RPM rising too fast compared to speed in the data). It has an open diff that Infiniti optimistically called a B-LSD for "Brake Limited Slip Diff". It does good straight line standing start 11s but it is woeful on the track. Nismo seem to make a 2 way for it.
    • Also, I logged some data from the ECU for each session (mostly oil pressures and various temps, but also speed, revs etc, can't believe I forgot accelerator position). The Ecutek data loads nicely to datazap, I got good data from sessions 2, 3 and 4: https://datazap.me/u/duncanhandleyhgeconsultingcomau/250813-wakefield-session-2?log=0&data=7 https://datazap.me/u/duncanhandleyhgeconsultingcomau/250813-wakefield-session-3?log=0&data=6 https://datazap.me/u/duncanhandleyhgeconsultingcomau/250813-wakefield-session-4?log=0&data=6 Each session is cut into 3 files but loaded together, you can change between them in the top left. As the test sessions are mostly about the car, not me, I basically start by checking the oil pressure (good, or at least consistent all day). These have an electrically controlled oil pump which targets 25psi(!) at low load and 50 at high. I'm running a much thicker oil than recommended by nissan (they said 0w20, I'm running 10w40) so its a little higher. The main thing is that it doesn't drop too far, eg in the long left hand fish hook, or under brakes so I know I'm not getting oil surge. Good start. Then Oil and Coolant temp, plus intercooler and intake temps, like this: Keeping in mind ambient was about 5o at session 2, I'd say the oil temp is good. The coolant temp as OK but a big worry for hot days (it was getting to 110 back in Feb when it was 35o) so I need to keep addressing that. The water to air intercooler is working totally backwards where we get 5o air in the intake, squish/warm it in the turbos (unknown temp) then run it through the intercoolers which are say 65o max in this case, then the result is 20o air into the engine......the day was too atypical to draw a conclusion on that I think, in the united states of freedom they do a lot of upsizing the intercooler and heat exchanger cores to get those temps down but they were OK this time. The other interesting (but not concerning) part for me was the turbo speed vs boost graph: I circled an example from the main straight. With the tune boost peaks at around 18psi but it deliberately drops to about 14psi at redline because the turbos are tiny - they choke at high revs and just create more heat than power if you run them hard all the way. But you can also see the turbo speed at the same time; it raises from about 180,000rpm to 210,000rpm which the boost falls....imagine the turbine speed if they held 18psi to redline. The wastegates are electrically controlled so there is a heap of logic about boost target, actual boost, delta etc etc but it all seems to work well
    • hahah when youtube subscribers are faster than my updates here. Yes some vid from the day is up, here:  Note that as with all track day videos it is boring watching after the bloopers at the start.  The off was a genuine surprise to me, I've literally done a thousand laps around the place and I've never had instability there; basically it rolled into oversteer, slipped, gripped and spat me out. On the way off I mowed down one of the instructor's cones and it sat there all day looking at me with accusing cone eyes as I drove past. 1:13:20 was my fastest lap, and it was in the second session, 3rd lap.  It (or me!) got slower throughout the day as it got hotter.      
×
×
  • Create New...