Jump to content
SAU Community

Recommended Posts

Hi all,

I need to clean out the garage, I have the below parts for sale.

These are all from my 2door R34 Gt-t that I no longer have.

Genuine S1 R34 Gt-t front bumper, a little cut up for a FMIC but still in overall good condition – $80.00

ZRv5tOWh.jpg

6FjW6rQh.jpg

Stock R34 Gt-t 2 door exhaust - $150.00 - good condition

pyGRdQFh.jpg

Stock R34 Gt-t suspension + front & rear sway bars $100.00

tT3bEiah.jpg

Stock R34 Gt-t wheels, rubber is in fair condition - $200.00

34uxatWh.jpgWugMJGjh.jpg

Genuine Bosch Mass Air Flow Sensor, brand new in a box, purchased but never used - $150

t5u5QEm.jpg

Tomei Z32 Mass Airflow Meter, brand new in a packaging, purchased but never used - $15.00

JeECadd.jpg

Apexi Power FC and hand controller for R34 Gt-t, purchased 2nd hand and never used – $800.00

HPiBvVS.jpg

cOZJbLK.jpg

Please PM me for any info.

Pickup preferred, North Shore of Sydney

MikeyG

Edited by mikeyG

Suspension no longer available.

I also have these additional items to add to the list.

NIZMO Resin Gear Knob, great condition - $20.00

http://i.imgur.com/sInch0q.jpg

Stock orange front and side indicators great condition - $40.00

http://i.imgur.com/nkqS4FW.jpg

Edited by mikeyG

Interested in standard 34 wheels, what's the tread like? I'm going on holidays for 2 weeks so will be able to buy after I come back if they're still available

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
    • Punch your VIN (nm35-xxxxxx) into Amayama.com You can see everything there quite easily.
    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
×
×
  • Create New...