Jump to content
SAU Community

Should Coilovers Be This Hard To Adjust?!

NZa31

By NZa31,
in Four Door Family & Wagoneers

 Share

Recommended Posts

NZa31 Apprentice

NZa31

Posted
Posted

Hey guys, I recently got some new coilovers for my cefiro and I'm having some trouble adjusting the ride height on the rears. When they are out of the car they are really easy to spin the threaded part of the shock up or down in the body to adjust height but when they are bolted into the strut tower and onto the hub carrier the are super hard to spin with the adjusting spanners, the only way to spin them easily is with a long bar on the end of the spanners and it makes an awful squealing noise. I've CRC'd the thread but still the same. Seems like there's side ways pressure on the coilovers and it's not wanting to spin freely. Only suspension mods in the rear are adjustable camber and toe arms, gtr sway bar and s14 hubs. Sorry for the novel length post but any help would be great!

  • 3 weeks later...
colourclassic Mentor

colourclassic

Posted
Posted

There would be some upward pressure applied to the damper by the sway-bar, as well as the lower mounting bush applying lateral load, but that shouldn't be enough to make it that difficult to turn the adjuster. Have you inspected the threads for damage since they were mounted?

V28VX37 Veteran

V28VX37

Posted
Posted

... When they are out of the car they are really easy to spin the threaded part of the shock up or down in the body to adjust height but when they are bolted into the strut tower and onto the hub carrier the are super hard to spin with the adjusting spanners ...

I've had similar experience but in the front, BC Racing coilovers being hard to adjust on an R34. Rears spin easier.

The only way I've found to make it a bit easier is to move the LCA up or down slightly, I've used a separate jack under the wheel hub when the wheel is off. It seems that there is some vertical tension in the whole suspension assembly that you have to get out in order to make adjusting the height easier.

I'm also keen to know if there's an easier way?

NZa31 Apprentice

NZa31

Posted
  • Author
Posted

They are brand new and the threads are mint. There seem like a lot of side ways pressure on the coilover which is stopping the thread from spinning easily. I also tried a separate jack on the hub to take a bit of tension up but no luck. Could it be anything to do with the s14 hub carriers being different to s13/a31? Thanks for the replies

GH05T Grand Master

GH05T

Posted
Posted

same in the stagea, rears are easy but the loan on the fronts make it a bitch. mine were still movable just with a squeal. or yeah undoo the base and take the load off to adjust.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      Have a look at that (shitty) pic I posted. You can see AN -4 braided line coming to a -4 to 1/8 BSPT adapter, into a 1/8 BSPT T piece. The Haltech pressure sender is screwed into the long arm of the sender and factory sender (pre your pic) into the T side. You can also see the cable tie holding the whole contraption in place. Is it better than mounting the sender direct to your engine fitting......yes because it removes that vibration as the engine revs out 50 times every lap and that factory sender is pretty big. Is it necessary for you......well I've got no idea, I just don't like something important failing twice so over-engineer it to the moon!
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • funkymonkey
      Jacks that fit under GTR lips that can reach the subframe?

      By funkymonkey · Posted

      I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
×
×
  • Create New...