Jump to content
SAU Community

Recommended Posts

the other day i uped the boost on my r33 so that it know runs around 10-11 psi but dont know if this model has a boost cut or i have some bad fuel, or maybe time for some knew plug. once it gets boost of 10-11 it splutters and pops through the exhaust. the plugs have done 25000 kms and the fuel im using is mobil.

Link to comment
https://www.sau.com.au/forums/topic/43586-boost-problem/
Share on other sites

sorry as far as i know they have a boost cut for over boosting, I ran 14psi and no drama's, my car did suffer a broken land on piston 6, just when i bought it, because of a failing fuel pump, I found out after the rebuild that the fuel pressure dropped away under load. this was before I did any mods to it. a new 044 and she was a steady pressure again.

Link to comment
https://www.sau.com.au/forums/topic/43586-boost-problem/#findComment-891084
Share on other sites

Cav its your plugs, I just went through the same prob last weekend, car loosing power like spark or fuel cutting at anything higher than 9psi.

I replaced the plugs from fairly new NGK's to Double Platinum Autolits $90 all up and was advised by two different GTR specialist one online in N.Z skylinesdownunder forum to gap them to .66 So I took them as close as I could to that and guess what, it bloody worked, boost is fine all the way to 12psi - not game to take any further till I get a front mount.

Link to comment
https://www.sau.com.au/forums/topic/43586-boost-problem/#findComment-894992
Share on other sites

i found iridiums to be shite in my S13 ... soon as i upped the boost with an EBC it started missing. took the iridiums out and put in just your normal cheapy plugs that are like 12$ a set and it worked a treat. id say find out what is the cheap copper alternative to your plugs (NGK brand still though) and put some of them in at the same gap of .75-.8. for $12 it cant hurt to see if it is just crappy plugs.

yeah u need to dyno your car with a fuel pressure guage to test the fuel pressure. however, if you are upping your boost, it is a sensible option to upgrade your fuel pump anyway, especially if your planning to run the higher boost all the time and more power in the future. an 044 intank replacement is usually a good bet.

if it still has issues and you want to go for a Malpassi pressure regulator, do that after you've done the fuel pump. the Malpassi wont do much good if you have a stock fuel pump coz the pump will struggle to keep up the increased pressure anyway. i had a misfire in my DR30 skyline, changed plugs and leads, reset ecu, upgraded fuel pump, and still had a misfire at around 1bar. after fitting a Malpassi Rising Rate regulator the misfire is now gone.

try plug changing and see how you go to start with though!

Link to comment
https://www.sau.com.au/forums/topic/43586-boost-problem/#findComment-902830
Share on other sites

guys i have changed the plugs with a set of ngk cheapies and still the same. got my mates to watch the ass of it and it is blowing raw fuel out the exhaust. do they have trouble with the coils, maybe one doesnt like the increased boost (extra load). it doesnt play up till high in the revs 5000-6000 rpm. i can run 10-11 psi low in the revs with no trouble.

Link to comment
https://www.sau.com.au/forums/topic/43586-boost-problem/#findComment-909192
Share on other sites

  • 3 months later...
sorry dude havent sorted the problem yet, am thinking coils, or an after market computer its got me stuffed need to get it to someone whos playing with them all the time. i might sell it yet, that will fix it.

luckily it seems it was just my plugs...I hope you get yours all worked out though. Good luck!

Link to comment
https://www.sau.com.au/forums/topic/43586-boost-problem/#findComment-1054385
Share on other sites

guys i have changed the plugs with a set of ngk cheapies and still the same. got my mates to watch the ass of it and it is blowing raw fuel out the exhaust. do they have trouble with the coils, maybe one doesnt like the increased boost (extra load). it doesnt play up till high in the revs 5000-6000 rpm. i can run 10-11 psi low in the revs with no trouble.

Sounds like a fuel problem dumping too much fuel in and choking on it if its coming out the exhaust as a liquid :uhh: - SAFC ll can fix this.

Could be the coil packs, you'll need to tape them up with duct tape. Because the spark can ark out the side which results in the plug not getting the full spark. Do you run the black cover ontop of your coils - Saying Nissan 2498cc etc... ?

Hope that helps.

Link to comment
https://www.sau.com.au/forums/topic/43586-boost-problem/#findComment-1054433
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • One year is a bit concerning. Did you try contacting GSP? It says 5 year warranty on the box if I remember correctly. I'm also running their driveshafts on my S2 Stagea.   You could check the part numbers on Amayama for your year. Here's the link for my 1998 which gives the 39100-23U60 part number. Well, that and 39100-23U70. https://www.amayama.com/en/genuine-catalogs/epc/nissan-japan/stagea/wgnc34/6649-rb25det/trans/391 What does it say for yours?
    • I ordered a GSP Front R/H Axle from here - https://justjap.com/products/gsp-premium-front-driveshaft-r-h-nissan-r32-r33-r34-skyline-gtr-stagea-4wd#description It lasted around a year before one of the boots blew out. I'm lowered, but I have GKTech roll center adjusters. One year seems a little premature. I think I'm going to spend the extra money on an OEM cv axle this time. This website - https://tfaspeed.com/collections/nissan-stagea-wgnc34-x-four-parts/products/nissan-stagea-awc34-260rs-rb26-right-front-axle-drive-assembly Makes it sound like the readily available OEM CV axle will only fit 11.1999 Stagea and up (mine is a 2.1997 S1). The JustJap listing didn't mention any years or anything for the GSP axle. Amayama shows '11.1999' and up as well for that part number. As well as 'plastic boot type'. See attached picture. So I guess my question is, does that axle (39100-23U60) really only fit S2 Stagea? It's the front driver side. If it does, I'd love to buy that instead of rolling the dice on another GSP. I've found that OEM one cheaper here: https://www.partsfornissans.com/oem-parts/nismo-jdm-r32-r33-r34-skyline-gtr-r32-gts4-right-front-axle-3910023u60 and here https://www.nissanparts.cc/oem-parts/nismo-shaft-ft-drive-3910023u60 Just a little confused because the JapSpeed listing for the GSP front driver axle doesn't mention any specific years or anything and it fit my S1 Stagea fine. So will 39100-23U60 fit my S1 Stagea even though technically it says '11.1999' and up? What would have changed? Thanks.  
    • Thanks for the info. The only "Issue" I've had with the shifter is I always found the throw between 4th and 6th gear too close. I'm always worried to shift into 4th accidently and sending my motor to the moon. Adam LZ recently came out with a video and stated Serialnine revised their shifters to correct this and will change all the revised parts for 150$. Strangely enough, I contacted Serialnine right after and they denied it and said it's bullshit. I found that strange as he's a distributer. I'll keep this forum post updated on that saga.
    • Yep that is correct. It allows you to adjust the short throw range from what I can tell
    • Car has been running great, I've put about 300km's of break in time on it. First thing that stands out with properly sealing rings is no more noticeable crankcase smell coming out of my catch can. This may seem insignificant, but the constant smell while driving around was infuriating. It's also nice to see my oil level remain stable. Two new issues have developed that I only noticed this weekend though. There's a very noticeable driveline vibration past 100kmh. I only noticed it now as I've been babying it under 100kmh in the backroads. This comes as no surprise as I'm running a one-piece shaft, and I paid zero attention to my driveshaft angle when I put everything back in. I also have a fair bit of voltage drop on hot starts. The starter audibly is forcing. No issues on cold start though. I must not have removed all the paint under my main block ground during assembly. I'll try and take care of both those issues this week once the kids are asleep.  I also received all the parts I was missing for my direct port setup. I will hopefully have pictures of that up soon. I'm hoping to get back on the dyno the week of June 30th as I'll be on vacation. I'm confident I should be able to make north of 500rwkw on pump gas and WMI. I'll go back again later this summer with E98, but I want to confirm my ethanol content sensor is working properly first. I've never seen it read anything but 11%. This makes sense for our 10% ethanol content pump gas here, but I would expect the occasional movement between fill ups. 
×
×
  • Create New...