Jump to content
SAU Community

(Sa) R33 Lowering Springs From R33 Gtst

GeeDog
 Share

Recommended Posts

GeeDog Experienced

GeeDog

Posted
Posted

Full set of Eibach lowering springs for R33 Skyline GTST (probably fit other models but not sure)

Rears marked as 51,96 6340102, fronts are 50,96 6340101.

With these springs fitted ride height was around 330mm front & 340mm rear - measured centre of wheel to wheel arch - $125

Prefer local pickup but can post at cost.

post-98010-0-27515000-1386301899_thumb.jpg

post-98010-0-22924600-1386301892_thumb.jpg

post-98010-0-86278700-1386301884_thumb.jpg

GeeDog Experienced

GeeDog

Posted
  • Author
Posted (edited)

Best I can do - this was from the Gumtree ad when we bought it. The ad is now closed and this thumbnail is all that's left.

We measured height at 330mm front & 340mm rear, from centre of wheel to guard. It wasn't sitting on the ground, but lower than we've got it setup on coilovers.

post-98010-0-99654500-1386915252.jpg

Edited by GeeDod
  • 7 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By GTSBoy · Posted

      I hadn't thought about the variable power steering assist. Presumably, it will always be the same level of assist as you get in an S14. The R32/3/4 are either helliishly heavy (at low speeds) if the solenoid is not powered at all, or hellishly too light (at high speed) if it is powered all the time. I presume that it is PWM controlled on those cars. I hadn't thought about the S cars not having variable assist. ugh. What crappy plebby cars they must be!  
    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      Hmm yeah that is a good point. It looks like it'll just bolt in with no real issue besides maybe the bushings being different. My other concern was that 2 pin plug that I assume is used in some way to control the rack solenoid depending on the speed signal from the ecu. The DMAX rack doesn't even have that plug though so, don't think it'll matter. Might just order the rack and see how it goes. Will update this when I figure something out
    • GTSBoy
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By GTSBoy · Posted

      I'd say it's a fair bet that the feed and return fluid lines will be in different enough spots that you would need to come up with a way to cut the originals short and adapt with new hard line adaption or braided teflon hoses or somesuch. But really, you have the car, you have the photos of the DMAX rack - you should be able to go out there and see for yourself whether they're in the same or different spots.
    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      I've been doing some looking around and honestly was just considering throwing a new rack at it. I saw that the dmax silvia rack bolts up into the 33 with the silvia bushings but not sure if the high pressure lines will sit in the correct spot. I believe other version of the 33 rack are the same/similar to the racks that can be opened up without as much fuss so I assume the dmax rack would fit but any ideas?
    • GTSBoy
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By GTSBoy · Posted

      I've never played with one, but I would expect that you are correct. That slot looks like it is intended to be used to unscrew the end, and the flats on the body would be better than grabbing it around the round bit with a pipe wrench. So, yeah, probably unscrews. You'll probably have to make a tool to drive in that slot.
×
×
  • Create New...