Jump to content
SAU Community

How To Get Rid Of Sluggish Coldstart/warmup And Bad Fuel Economy On Your Nistuned Rb20Det/z32/gtr Ecu.


Rolls
 Share

Recommended Posts

  • 1 month later...
Who knows then!

Hey rolls quick question about this

Can you make these changes via a trail version of nistune?

I don't want to pay a workshop in ACT to make these small changes because I'm sure they will try charge an arm and a leg and DVS lives too far away for something this small

Link to comment
Share on other sites

Pretty sure they don't make a trial version of nistune anymore, you should email pete/matt and say this is the only change you want to make, they might be able to help you out or point you in the direction of someone who can do it for basically free, they are both good blokes so I'm sure they will at least suggest something.

If they do have a trial version, let us all know!

http://www.nistune.com/contact.php

Edited by Rolls
Link to comment
Share on other sites

That's a shame that people do that Matt.

As it would take literally 5minutes, perhaps your tuner could make the changes for free or cheap as Manuel Kasko, especially as you are bringing in a bit if knowledge for them to help future customers.

Edited by superben
Link to comment
Share on other sites

That's a shame that people do that Matt.

As it would take literally 5minutes, perhaps your tuner could make the changes for free or cheap as Manuel Kasko, especially as you are bringing in a bit if knowledge for them to help future customers.

Tuner is about 4 hours drive from here.

ACT Nistune tuners will probably charge me too much for the changes.

Link to comment
Share on other sites

Changes are disabled in the trial now, because some people would tune customers cars using the trial version!

If people are so cheap they won't spend the $200 to get a personal license (even though they should get a tuners license) then I doubt getting rid of the trial version will stop them, they will probably just steal someone elses license code or get 20 people to chip in and do that.

Do you have checks in the software to stop people sharing license keys?

Link to comment
Share on other sites

Tuner is about 4 hours drive from here.

ACT Nistune tuners will probably charge me too much for the changes.

Why not give a tuner a call? explain exactly what you want them to do, surely they wont charge you more than $20 for a 5 minute job.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share




  • Latest Posts

    • You won't make it out of your driveway. Both your rear wheels will go in whichever direction they feel. Your Hicas rack or a lockout bar is required to keep your wheels straight. 
    • Updating results.  Using ATR45SS-0 model VS UHF57-900. Those two are very different turbos, different wheels sets with different wheel hub profiles but yet with almost identical result. I’m intrigued with both turbos performance. ATR45SS-0 was a 61mm turbo first developed in May 2020, UHF57-900 was a 62mm turbo developed in March 2024 as a powered up alternative of a G30-900. On paper ATR45SS-0 maxed at 563rwkws, while UHF57-900 maxed at 568rwkws. ATR45SS was slightly more responsive with slightly better power band through the mid range.  Road driving ability, ATR45SS-0 had better throttle response, felt more robust under throttle, as it wakes up earlier. I think G series wheel hub design made it to have higher inertia under light throttle. Doing bit more prototype work in the next few weeks, will update result when its back on dyno again. ATR45SS0 Blue, UHF57-900 Red Chequered tuner's Dynapack hub dyno, E85 fuel. Mod list is in video below video_20240604_114214.mp4    
    • Did you run the power cables for the mac valve to the other side of the car near the fusebox? Utilizing the stock boost controller cables? or did you run new ones?
    • Hey I have a potentially stupid HICAS question 🤣 I'm currently doing a full hicas delete, Power steering pump modified to non hicas, all lines removed from the car along with all electronics. My stupid question is - Do I need a lock out bar? is there any reason why I cant just remove everything from the rear end? I already have a lock out bar but thinking to save a few extra grams I could also get rid of the arms and tie rods as well and just run it with nothing in its place? or would it have a negative effect on handling?
    • Hi how are you guys?  I know i have been absent for years but im coming back slowly guys just wondering if anyone know where the ball joint on the NISMO arm front and rear can be replaced with OE parts?  Also  i know this is not the thread looking for springs and blistein shocks for the 260rs. Please advcie     cheers    yudy
×
×
  • Create New...