Jump to content
SAU Community

Recommended Posts

Hey guys,

So my friend who was going to be doing the suspension this afternoon has ended up cancelling on me.

I'm stuck in a situation that I have either today or tomorrow to get the stock suspension into my R33 ready for my inspection and before I go on holidays.

Can someone pm me a price if they have time

Link to comment
https://www.sau.com.au/forums/topic/436659-cash-job-asap/
Share on other sites

I can't thank Pat enough for his efforts lastnight!
Ended up that the last person who put the suspension on got the bolt stuck in there.

Pat ended up snapping the 10mm bolt trying to get it out.

This then turned into a very lengthy night of replacing the whole rear left hub.

I think I managed to climb into bed about 1am.

Pat you are a life saved and I definitely owe you one

  • Like 2
Link to comment
https://www.sau.com.au/forums/topic/436659-cash-job-asap/#findComment-7152328
Share on other sites

Try owning a 32.

Every second thing you take off breaks or is totally stuffed.

Anything plastic is so fragile form age, buy a new one before it comes off, cos they always break.

Thats why half my interior is carbon wrapped.

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/436659-cash-job-asap/#findComment-7154181
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...