Jump to content
SAU Community

Csc Bmax Ark Design Brakes

SimonR32
 Share

Recommended Posts

SimonR32 Grand Master

SimonR32

Posted
Posted

Hi guys,

Have a set of CSC (AKA Bmax or Ark Design) brakes for my R32 GTR. They are 4 pot 343x32mm jobbies and I have managed to crack the disks so I need to replace them.

I'm finding it difficult to find replacement rotors that will fit my current hats as the PCD appears to be (at my best ruler measurement) 222mm while the most common PCD for this size appears to be 215.9 and also 228.6. I guess my other option would to buy or have some new hats made with the more common PCD but that's starting to be big dollars.

If all else fails I think I can get some replacements from Ark Design but as my current ones has cracked fairly badly I'm trying to source new options, any ideas or suggestions?

Cheers

Simon

Link to comment
https://www.sau.com.au/forums/topic/436846-csc-bmax-ark-design-brakes/
Share on other sites
BBGTR Experienced

BBGTR

Posted
Posted

I've used these brakes for 7 years on my R32 (although they are 355mm 6 pot fronts) and have been through a few rotors. There are $750 a pair, which is pretty good value. The next real option is to go to Harrop and pay ~$1,000 each. They'll last longer however I don't think the extra life makes up for the cost based on my experience.

Looking at your front rotors in your build thread, they don't look like BMAX originals as BMAX are all 36 vane. Did you buy the package new?

I would confirm the PCD with Sebastian at Ark Design and go from there. ALCON and AP would also be other options if you really wanted to go with other options however I'm unsure of the cost.

SimonR32 Grand Master

SimonR32

Posted
  • Author
Posted

Given that track days are harder on rotors than racing, you have done remarkably well considering how much meat was taken off :)

I wasn't blaming the rotor, just looking for viable options. I've sent Ark Design a message on ebay, hopefully will get a response soon

gmr Collaborator

gmr

Posted
Posted

Kit came of my white S15, good to see them getting used properly Simon.

They were on the car when I bought it from ARK (demo car). Fyi did maybe 1500-2000 street driving from memory before the car came off the road. Prior to that I'm not sure what ARK put them through.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...