Jump to content
SAU Community

Recommended Posts

Wasn't keen on starting a new thread..

R32 gtst - RB20DET

When I start the car whether its first thing in the morning or after the car is hot; The car sits at 1500-1700 RPM and doesn't drop... Ever, also has a spluttering/popping noise on idle & deceleration..

It's slowly getting higher & higher for example about 2 months ago when I started driving it after about a year off the road it was between 1200-1400..

I've gone through 3 different coilpack sets, same problem.

Cleaned AAC, same problem.

Found 2 small vacuum leaks, still didn't fix the problem..

Next will be injectors I guess.... Or any other opinions?

I'm actually taking the car to Gavin Woods at southport to plug the ECU in and see if any fault codes pop up.. So might tell me the problems cause.

Edited by ZRBE
Remove the air feed hose from the crossover pipe that runs to the idle speed control gear and block both openings. See what happens then. If it continues to run fast, then air is getting in somewhere else.

Will do, thanks man! Damn you have some knowledge... Aha

EDIT: So my car should stall after blocking both openings?

Edited by ZRBE

I wouldn't do it running unless you can do it quickly, because you will be opening big holes into the air flow. But if you were to do it with the engine off and could restart it (maybe needing some throttle opening) and it then stalls or chugs along at 300 rpm sounding like a kero engine....then the air flow path to your fast idle would appear to be through the idle control valves. If it continues to run fast, then not so much.

  • Like 1
I wouldn't do it running unless you can do it quickly, because you will be opening big holes into the air flow. But if you were to do it with the engine off and could restart it (maybe needing some throttle opening) and it then stalls or chugs along at 300 rpm sounding like a kero engine....then the air flow path to your fast idle would appear to be through the idle control valves. If it continues to run fast, then not so much.

Okay, so to get this straight if I do this and engine runs at 300Rpm or just stalls; There is no vacuum leak?

But if it continues to run higher rpm, it's safe to adjust the 'idle control valve'?

Sorry lol..

That's alright. If it runs slow or stalls then the problem (whatever it is) is in the idle control gear (either the fast idle/cold start thingo or in the ECU controlled AAC). If it continues to run fast then your air flow path is somewhere else - some other broken vacuum hose or gasket or whatever.

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I've never played with one, but I would expect that you are correct. That slot looks like it is intended to be used to unscrew the end, and the flats on the body would be better than grabbing it around the round bit with a pipe wrench. So, yeah, probably unscrews. You'll probably have to make a tool to drive in that slot.
    • A bit late but A disk S13P fit over stock R32 GTR brakes, usually A disk front, O disk rear works.
    • Or, the height of the release bearing is not correct for your combo. Start with the bleeding and checking the slave moves throughout its range when you press the pedal (2 person required), but it is possible for the height to be internally wrong too (box back off to measure.
    • Yes, there's quite a few things that can go wrong during a clutch install. Very unlikely. I have a similar clutch. They (ACS) make good gear. No, it is not normal. It is possible that you just need to bleed the clutch slave. But the new clutch will also have a more aggressive actuation force/pressure, and so your old slave cylinder might be a bit leaky or otherwise compromised, and not up to the extra force required. Or the master cylinder, same.
    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
×
×
  • Create New...