Jump to content
SAU Community

What not to do when your RB25DET gets rebuilt!!!

Steg33

By Steg33,
in Engines & Forced Induction

 Share

Recommended Posts

Steg33 Community Regular

Steg33

Posted
Posted

Just had my RB25DET fully rebuilt with forgies and all the machining to match and it's been run in properly with the mineral oils etc... The only downfall is that the ECU that was in it is a remapped Jap chip and mustn't have been tuned real or had parts changed since. So without over boosting it, the picture attached is what happens when you don't put it straight on a dyno. A bit of a learning experience (expensive learning) but just a warning to anyone looking to rebuild, don't assume your ECU will be ok for running in because obviously your motor died for a reason!!

If you want to make a grown man cry, melt his new forgies! :)

Steg33 Community Regular

Steg33

Posted
  • Author
Posted

The even worse thing is that the car was booked in to get finished and the Power FC was sitting on the passenger seat looking at me waiting to put in and be tuned when the white smoke started appearing in the rear vision mirror again.

This time all is taken care of, motor's just gone back in and the car should be on the dyno in the morning. Hoping for some nice figures soon.

Steg33 Community Regular

Steg33

Posted
  • Author
Posted

Paying cost for the parts and the labour is for nothing because Benny (ex-BMT) @ Chasers is looking after me because of the bad luck. So i could have come out worse if i had to pay full price for everything + labour. That's about the only bright side of this.

Still crying tho because it's bye bye to the motorbike to pay for it.

Steg33 Community Regular

Steg33

Posted
  • Author
Posted
Ouch, what new turbo is gonna be strapped onto the side?

It's already got a 3037 internal gate on it when it got the first rebuild so the turbo hasn't even had a chance to boost up yet.

Motor was started this arfternoon and the car is being trucked down to Race Pace to be put on the dyno in the morning. Now got the Q45 AFM and PFC in it.

Duncan Grand Master

Duncan

Posted
Posted
The even worse thing is that the car was booked in to get finished and the Power FC was sitting on the passenger seat looking at me......

I feel the pain, my sump baffles were sitting in the boot :D

Steg33 Community Regular

Steg33

Posted
  • Author
Posted
Damn thats crazy. If it had just been freshly rebuilt, why did you give it a bootful anyway? LOL

Anyways good luck with the new rebuild...

It never copped a bootfull, that's the thing. It was run in for about 3000ks running low boost and only got given a little bit lately just to drive it normally, never got past 5K rpm, not even near red line because i was paranoyed about the computer. Most of the ks were done commuting to uni.

Needless to say the computer i took out got stomped on and pieces broken off everywhere. Wasn't even going to be sold once it was named the cause.

GTRgeoff Grand Master

GTRgeoff

Posted
Posted

Are you sure the computer was the cause? I threw in a GTR fuel pump and it delivers so much now I have to use full mechanical advance to stop the motor choking on fuel when I want power. It uses so much juice that the hole in the ozone layer follows me around :D

Sorry to hear of your dramas. I too await the hallowed PFC install and refuse to drive the car until then.

Steve Grand Master

Steve

Posted
Posted
Isnt Load a result of RPM?

...

Load is measured by the AFM or MAP sensor (whichever it uses)

This is how maps are created, one axis is rpm the other load.

Imagine if you are at 2000rpm down a hill, compared with 2000rpm going up a hill - you use more throttle going up the hill, as the load is higher. So both cases use the same rpm referrence, but different load referrence

T0nyGTSt Grand Master

T0nyGTSt

Posted
Posted
I threw in a GTR fuel pump and it delivers so much now I have to use full mechanical advance to stop the motor choking on fuel when I want power. It uses so much juice that the hole in the ozone layer follows me around :D

 

Sorry to hear of your dramas. I too await the hallowed PFC install and refuse to drive the car until then.

Tell me your MPG and I'll beat you no problems :(

When I had my motor rebuilt I ran it for 2,000km before a dyno tune.

It had the old road tune on the maps already.

Can was extremely terrible on fuel early on - like as if friction were high (???) and things need bedding in.

I had a Bosch 44 fitted and the car was terribly surgey... like as if too much fuel.

Ran it on a dyno, car went back to normal response.

Did a thorough road tune via laptop, car is more surgey new, better response but fuel useage is dead on 'normal' for this type of car (ie. high but hardly worth a raise of the eyebrow).

T.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      NC MX5

      By The Bogan · Posted

      Like I said, "black magic" LOL In the end,  it is what it is, and hopefully, what this here knuckle head has done is an improvement and not a hindrance Not that I actually notice any negatives now, or that I will get any seat of the pants benefits when all is said and done, but best practice says I shouldn't be pulling intake air from the hot engine bay  Famous last words: I cannot see it being any worse than what it is at the moment 🤔
    • GTSBoy
      NC MX5

      By GTSBoy · Posted

      If the gases flowing in those two tracts had the same properties, you could maybe use such broscience. But the exhaust has a different composition, different normal density, different actual density (because of different normal density, and mostly because of the massively higher temperature), and different viscosity (again because of much higher temperature). Consequently, all of the fluid dynamics parameters that matter, that you calculate from these inputs, such as the Reynolds number, friction factors (for wall friction) and so on, are all incomparable.
    • GTSBoy
      Ethanol Content Sensor - Always at 11%?

      By GTSBoy · Posted

      And we shall have to presume that Canada is the same?
    • joshuaho96
      Ethanol Content Sensor - Always at 11%?

      By joshuaho96 · Posted

      In the US almost everything is E10. It can't exceed 10% by much or fuel systems have trouble adapting. At the same time because MTBE, MMT, and TEL are all banned they need as much ethanol in it as possible to boost octane.
    • Kinkstaah
      NC MX5

      By Kinkstaah · Posted

      I was mostly jesting. In my experience (and probably only my experience) the R34 GTT physical airbox space is actually too small to flow the amount of power it wanted. By sealing the box, I made it so it could only be fed by the ducts themselves. So you can seal it up and get nice cold air which IS good, but at a certain crossover point: More Hot Air > Less Cold Air I don't think you're at this point. In my case merely ducting the hot air intake with a very focused set of ducts counteracts the fact it's in a V8 engine bay. More cold air obviously best. The solution looks great.
×
×
  • Create New...