Jump to content
SAU Community

Recommended Posts

I just asked the question. coz my car had a label of unleaded. not sure what rating it was.

Plus i have read somewhere that E85 mixture is ok for the car too.

But i do agree with people here. i get more mileage on my cars when its on 98ron. runs better goes longer.

According to the FSM, the ECU switches to a 'knock map' when it detects knocking. But I have never observed it or tried to trigger it.

Yes, but there seems to be this perception that the ECU "removes" timing when it detects knock on the fly.

I've never seen any evidence of it, when I played around with Uprev and set the knock map up, it is quite simply just another Ign timing table to set say 20 points lower than the standard table.

I just asked the question. coz my car had a label of unleaded. not sure what rating it was.

Plus i have read somewhere that E85 mixture is ok for the car too.

But i do agree with people here. i get more mileage on my cars when its on 98ron. runs better goes longer.

E85 requires a custom dyno tune, complete with a marginally larger set of injectors.

As above, you CANNOT dump a tank in and expect the car to run ok.

  • Like 1

Plus i have read somewhere that E85 mixture is ok for the car too.

Yeah good luck with all that.

Its amazing what other kids can tell you in the sand pit these days

Edited by Howaitonaito

sometimes its just good to know...hehe Thanks for the info guys!!!

fyi: my 350GT has never tasted petrol below 98ron in my care.

E85 requires a custom dyno tune, complete with a marginally larger set of injectors.

As above, you CANNOT dump a tank in and expect the car to run ok.

Yeah good luck with all that.

Its amazing what other kids can tell you in the sand pit these days

Yes, but there seems to be this perception that the ECU "removes" timing when it detects knock on the fly.

I've never seen any evidence of it, when I played around with Uprev and set the knock map up, it is quite simply just another Ign timing table to set say 20 points lower than the standard table.

Yes, i believe that is correct, it is just a 2nd map with a fairly heavy timing retard (and fuel mix richen).

The FSM specifically says the knock sensor is a 'last resort safety device' and is not a tuning device, so when knock occurs the ECU just smashes back the timing to try to prevent damage, it was not intended to 'adjust' to low octane fuels.

And the other false perception is the ECU uses the knock sensor to advance the timing for higher octane fuels.

the only ECU I know that actually uses multiple knock sensors to 'tune' the timing is the newer WRX STI ECU.

Well the article i read was from cars guide and not specifically talking bout our skylines but were talking about modern cars. Im guess anything over year 2000 is a modern car.

That is why there are forums like this to ask questions and get answers from experienced owners.

Thanks for your statement though.

:)

If that place you read that awesome piece of factual *cough* information also said the the boogie man exists would you believe them.

No.

Has anyone used e10 91 on their v35s?

Our cars can use 91ron but not sure if with E10 would work.

read me

http://www.unitedpetroleum.com.au/united/fuel/unleaded-e10

do a little homework ,...e10 is 95 octane...i dont know why the misconception I hear so often, I guess because its cheap eveyone thinks its low octane...Its 95 octane at cheaper cost....and yes it should be fine to run...run it in my 04 honda all the time...may get 50kms less a tank but at least i know my injectors are clean...

No way is e85 ok for your car.

some cars with high compression rates can run it ok., I know guys in USA have tested it in Hondas and it runs good and pulls harder faster than petrol.....

that said

Its still not a very good idea but if it were an emergency you can get away with it

You would be surprised how much e85 you can put in the tank before the ecu calls it quits and throws a code. Remember the o2 sensors in these modern cars are very good at re-calculating short term fuel trims. I have heard 50% is usually ok.

You would be surprised how much e85 you can put in the tank before the ecu calls it quits and throws a code. Remember the o2 sensors in these modern cars are very good at re-calculating short term fuel trims. I have heard 50% is usually ok.

But they run to AFR... Not lambda.

E85 and 98 have different stoich ratios. Which the O2 sensor can't take into account. It's fixed on 14.7- petrol.

Both have a lambda of 1 ( lambda is just the indication of the best or most efficient ratio). So you might then tune petrol to 11.5afr, however that isn't equal to the same ratio when using e85

As the sensor reads lambda it automatically compensates for different fuels. I tune e85 to 14.7:1 on my gauge and it is just as stoich as a petrol tune. (just remember, e85 isn't 100% ethanol anyway.)

United 100 octane is garbage. its not really 100octane since it uses 10% e10 to boost the octane rating. been using it until i got my car uprev tuned and now running shell 98, much better

you are a moron. octane is octane. it's a way of measuring any fuel. LPG has an octane rating too. E85 is ~105-110 octane depending on the exact blend.

United's E100 works really well. In my R33 it was noticeably better than 98RON.

Yeh, it's 100 octane ;) lol

I get poor economy using it compared to normal 98ron fuel.

Up to 50% worse km per litre (ie 250kms for 60L of United 100 compared to ~370kms with Mobil 98)

50% worse? It's either your right foot or something is seriously out of whack with your car. I ran United E100 all the time and it made almost no difference to my fuel usage.

E85 and 98 have different stoich ratios. Which the O2 sensor can't take into account. It's fixed on 14.7- petrol.

Both have a lambda of 1 ( lambda is just the indication of the best or most efficient ratio). So you might then tune petrol to 11.5afr, however that isn't equal to the same ratio when using e85

O2 sensors work by sensing lambda, not AFR. They measure the ratio of oxygen in the exhaust gas to oxygen in the air, and their output changes around lambda 1 regardless of fuel. The O2 sensor doesn't know you've squirted 14.7:1 worth of fuel into the motor, it doesn't care. All it cares about is how much oxygen is left in the exhaust gases and that is lambda.

  • Like 1

Ok, so let me try to understand this.

Hypothetically, you can fill up your stock as a rock car with e85, drive it around on closed loop, and have a e85 lambda of 1?

What is the e85 afr equilivent of 14.7?

No, because the stock ecu will only add or subtract around 10% of the fuel. Anything outside that range will trigger the MIL as the ecu will know something is seriously wrong.

Ethanol stoich is 9:1 I think. Not sure what e85 would be as I have never needed to know.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...