Jump to content
SAU Community

Recommended Posts

Hi , I'm looking for some help/advice.

I finally got around to putting coilovers in my bnr34 and was wondering what ride height others are running?

I have them at fairly even heights front and rear atm.

Any help would be awesome! Btw I have 19 rims.

Thanks :)

Link to comment
https://www.sau.com.au/forums/topic/439337-r34-gtr-ride-height-help/
Share on other sites

Rims make no difference, but rolling diameter must be the same within a few percent to be legal and to make sure your speedo is accurate.

IIRC all GTRs are the same with respect to hights (but i'm not 100% sure). So you want lowest of 350mm front 340mm rear (wheel centerline to guard). If you want higher, say if you have clearance problems under the car, then just make sure the front measurement is 10mm higher than the rear.

If you're going to track it, get it corner weighted after you've settled on the height you'll run.

You want the least amount of neg camber on the rear that works. So the usual range is about -0.75° to -1.0°. That tends to give the sort of compromise between straightline grip, tyre wear on the inside edge and cornering grip for a street car. A stiffly sprung track car on sticky tyres might want to run a lot more camber.

The same rules apply at the front but you can run a little more camber. Up to -1.5° is the normal range. But again, your mileage may vary, depending on how the car is used, the tyres, etc.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I mean, I can confirm the TPS is at 100%.... I can confirm when we installed the TB and setup the cable that the TB was indeed fully open at max pedal travel.. the same 'curve' (WRT MAP vs MAP) existed with the previous setup/TB/manifold as well... No, we did not do a run with no intake connected. I would love to go back in time to do such a run to rule out the intake. It would have also been good to do a run with the airbox lid off. There's a test there where increased IAT vs more available air could be a positive tradeoff. I remember taking the lid off my R34 Turbo setup back in the day and noticing a monster increase, even if IAT's did go up. Could be similar. Hard to test unless I find a very deserted road. 
    • That's actually encouraging to be honest. my motor was rebuild many years ago but it's probably done less than 30,000kms and fucc all limiter or drift, majority street / drag / roll racing. It'll be fine 💪🏼 I don't even have lines or a can for the cam breathers installed yet, there is zero oil residue or splatter on or around them, it drives beautifully so it seems healthy. Just a ticky lifter, yet they're almost brand new oem genuine Nissan and haven't done many kms at all...
    • Have you confirmed the throttle body goes to WOT (and stays there) during the run?
    • I'm having a problem. I think it was mentioned above somewhere but can't see it.  I'm stuck in the cycle of, sand, filler, low spot again, put filler, sand, low spot again, now i put filler again and a thicker portion which seems to have helped but I got low spots in other areas. In the image. Circled in red thats where the original low spot was and the shape is the same as the red out line. I've more or less fixed that (still low spot up the top but now I have low spots where the green circled part is.  Is likely the issue that I didn't start with a course sand paper? I sanded the filler with 240 to reduce the risk of not going to far but maybe the issue is that I'm only taking off enough material to remove some of the filler but not the high spots. I now started sanding with 120 and I think I'm seeing a difference. I did fix one dent the other 2 are f**ked and seems like I made another low spot which is indicated by the furthest green circle on the left handside. Any thoughts and solutions?   Also second image. All of these rock chips, can they be filled in with primer or do i need to fill them all with filler/putty? So many rock chips on mine lol.
    • Well, I had an Edward Lee's special edition odo windback car/motor with a RB25DET S2 and I put down 372kW with a good amount of track abuse for 1.5 years before the ring lands decided it didn't want to stick around anymore 🥲 But probably didn't help I kept on smashing try limiter on the track and a few skid pans.
×
×
  • Create New...