Jump to content
SAU Community

Recommended Posts

  • 3 weeks later...

A reliable, working motor? :)

Seriously though what's the story with it now?

:domokun: Low blow.

I don't know, have not chased them up about it. About to settle on a new house so i'm sorting that out at the moment.

:domokun: Low blow.

I don't know, have not chased them up about it. About to settle on a new house so i'm sorting that out at the moment.

Sorry mate, had to ask.

You shouldn't have to chase them up really. Lucky for them you're too busy to. I dislike it when places take so long to complete what is ultimately fairly minor work.

Sooooo.........what did you get for the car?

http://www.jdmautolink.net/2015/03/nismo-365mm-steering-wheel-02-skyline.html

Will sit nicely with the interior overhaul i will be doing this year. :woot:

Majorly cool. btw I think i've seen a padded centre cover for the Nismo wheels somewhere too....

Nice, Get it!

Then I want to see videos of you driving around on the street with it!

Don't Hollinger build those? Might as well contact them to build you something suitable then buying one that's gone from Australia to Japan, got thrashed then sent back to Australia.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
    • My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
    • I thought the same to start with. But then I thought it was one of those LCAs where the end of the ARB goes through a bushing in the LCA itself, instead of having an end link.
×
×
  • Create New...