Jump to content
SAU Community

Recommended Posts

As title says I'm after a 3" exhaust. can swap standard plus cash if you want to go back to stock. I'm in Sydney and will pay freight.

Pm me if you want to sell.

Link to comment
https://www.sau.com.au/forums/topic/439973-wtb-3-inch-exhaust-for-m35-vq25det/
Share on other sites

I will probably be keeping the 3.5 system I have on the car now, which means the twin tip Nismo might be up for grabs... Are you after a cat back, or complete exhaust?

I will probably be keeping the 3.5 system I have on the car now, which means the twin tip Nismo might be up for grabs... Are you after a cat back, or complete exhaust?

If he ends up not interested I might be. How much would you be looking for and what condition is it in?

Scotty, I will be doing the full exhaust. But if will take a cat back to start with if its going for a fair price. Pm me price.

Thanks.

  • 3 months later...

kakimoto is the bomb i just love a cannon too i had the fujitsubo but didn't like it that much personnel choice

Flow is more important than noise to me, and the damn drone... It gets exponentially worse as you ditch the cats and go 3 inch to the turbo.

The Fujitsubo Legalis R has such a nice low note, and the design is near perfection imo. If only it didn't have dicky 4 inch twin tips.

Flow is more important than noise to me, and the damn drone... It gets exponentially worse as you ditch the cats and go 3 inch to the turbo.

The Fujitsubo Legalis R has such a nice low note, and the design is near perfection imo. If only it didn't have dicky 4 inch twin tips.

I would be ok with the twin tip, just wish I had the spare coin to buy one. I do agree they are the best sounding m35 exhaust Imo

i have a 3inch system i just bought a m35 and i want a standard exhaust this one has a decent system pm me if interested

Do you know what system it is? For the right one I would drive to vic to swap. I have the single tip nismo which is almost as quiet as stock but with much more flows

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
×
×
  • Create New...