Jump to content
SAU Community

Skyline V Series Replacement Transponder Keys, Problem Fixed

manuel
 Share

Recommended Posts

manuel Community Regular

manuel

Posted
Posted

Just to let everyone know that i have a contact in western sydney who can program your transponder key and make spare ones for you

This guy is a genious, he craked my BCM code and programmmed my keys, i now have 3 keys working. He can program remotes as well if they are on the same frequency as your original remote

He is very cheap and can supply keys for you,

Dont ask me prices, just ring him to discuss

Forget about Nissan Australia or Japan, he can do it all, any nissan car, this guy is a freak and well equiped with software

Contact Thai

0433790795

  • Thanks 1
sonicii Veteran

sonicii

Posted
Posted

Any locksmith that can clone the transponder chip should be able to make a working spare key. Problems arise when you have a new transponder chip with a preset code which needs to be programmed into you BCM. Sounds like you found a good locksmith that cares enough to find a solution for you.. nice work!

Zveruga Enthusiast

Zveruga

Posted
Posted (edited)

Just to let everyone know that i have a contact in western sydney who can program your transponder key and make spare ones for you

This guy is a genious, he craked my BCM code and programmmed my keys, i now have 3 keys working. He can program remotes as well if they are on the same frequency as your original remote

He is very cheap and can supply keys for you,

Dont ask me prices, just ring him to discuss

Forget about Nissan Australia or Japan, he can do it all, any nissan car, this guy is a freak and well equiped with software

Contact Thai

0433790795

mate, V series can be 35 and 36, and v35 can be done virtually by any locksmith. Which one is yours?

I am still looking for a solution for the v36, I've been to four dealers and countless locksmiths but nobody could really program a spare key for me

Edited by Zveruga
  • 2 weeks later...
manuel Community Regular

manuel

Posted
  • Author
Posted

My 2003 V35 key couldnt be cloned by any locksmith without the BCM code, believe me they tried and then referred me to nissan aus

My guy craked the BCM immobiliser code in 2 minutes, it saved me through to japan to get BCM pin number,

Foget nissan australia, they charge to much

My guy supplied me with 3 new chips which he programmed and now i have the original key plus two more spare

This guy can do V35, V36, any nissan skyline, ring him.......

sonicii Veteran

sonicii

Posted
Posted (edited)

My 2003 V35 key couldnt be cloned by any locksmith without the BCM code, believe me they tried and then referred me to nissan aus

Nothing needs to be done on the car if the key is cloned, the car doesn't even need to be available, the car just sees it as exactly the same as an existing working key.

My guess is the locksmith couldn't clone that particular type of keychip and used a new key with a new chip and therefore a new code which needed to be programmed into the BCM, thus requiring the BCM code.

Edited by sonicii

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Borci88
      Borg Warner EFR Series Turbo's V 2.0

      By Borci88 · Posted

      Not a problem at all Lithium, I appreciate your help regardless. I've pulled a small part of a log where the target pressure was 28psi and it spiked to 36.4psi. I've only just begun using Data Log Viewer so if I'm sending this in the wrong format let me know.
    • Lithium
      Borg Warner EFR Series Turbo's V 2.0

      By Lithium · Posted

      Sorry had a bit of a week and haven't had heaps of time to follow this, so apologies if I've missed something - any chance of showing a log with the rpm, turbo speed, MAP, and wgdc all in one view? Definitely an "interesting" problem, and while it's definitely worth noting that there was a similar issue with the twins I'd not completely put all bets on the root cause being the same thing.  Keep an open mind, follow the data.
    • Borci88
      Borg Warner EFR Series Turbo's V 2.0

      By Borci88 · Posted

      I built this engine approximately 12 years ago so my own head (brain) is a little grey on the exact hardware in the RB head, however what I recall is. Stock RB25 NEO TURBO Intake Camshaft HKS 260 degree Exhaust Camshaft (R34 GTR) RB25 NEO Turbo Springs  I ported/removed the exhaust stud humps found in the RB25 head so theres less turbulence but it wasn't ported/polished properly, just a hump removal. I've attached two pictures of the before and after to illustrate.     The ECU gets its boost reference from the nipple on the rear of the head on the intake side, behind the fuel rail. The wastegate gets its boost reference from a nipple on the cooler pipe immediately after the comp cover.  Could a decent pressure drop across the intercooler cause the wastegate to be seeing a higher PSI than what the ECU is seeing, and thus it can't control it accurately and quick enough?   We ran a line to the actuator and watched it open and close using an air compressor, while we didn't have a gauge on the line to see when it was cracking open, it was opening smoothly.  I just removed the gate now and even though the documentation says you need to open it in a vice due to preload (which I did), there wasn't any preload on the cap, which is something we noticed straight out of the box as well when new. This silver cap internally is threaded to the actuator rod that runs out the bottom of the straightgate. Not sure how I'm supposed to get this spring out to be frank.. Potentially but everyone else doesn't appear to have to stop at 500kw because of 6boosts design.  I would, but I think I'm getting to that point where if I'm going to do the head and make another 100kw, then I'm going to need a fancy gearbox and quite a few other things and 10k becomes 20k becomes 30k within a few months. I'm not necessarily sold on the idea just yet that the head is restrictive at 4000rpm (and what.. 300kw?) and yet doesn't seem to be restrictive at 7000rpm when it's making 500kw, however I'm obviously not closing the door on that theory.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      Yeah - Half the problem is I know this sensor actually goes to 150C.. I'm pretty certain it is min of 11C. So still more data required I suppose. It's really quite hard to get the oil temp to 100+ then immediately pull over and take a reading before the temp drops. Annoyingly I suppose the range I really 'want' is likely 80 -> 120C. TBH the ecu can't really *do* anything with it, and the gauge itself is very visible... ...but you know how it is.
    • The Mafia
      Borg Warner EFR Series Turbo's V 2.0

      By The Mafia · Posted

      My EFR 8474 Black, made 800awhp on a roller dyno. at 25-26psi. E85. Shaft speed was around 106,000rpm 1.01 rear. The rear is maxed.  6 boost Turbosmart 60mm gate 3.5inch exhaust  Head is worked to the shithouse. Bain racing. VCam. 272 exhaust. RB28 - RB26 foundation.  You have an intake issue. Start getting proper data and I mean go back to the simple things.  - Pressure test your intake - Block off the Turbo BOV, you don't need it.  - Test pressure before and after your intercooler If your head is pretty stock, that is your issue. Especially if it is NA.  Take it off and spend $10k on it. 
×
×
  • Create New...