Jump to content
SAU Community

[Bris] Fs: R33 Rb25 26 30 20 Ca18 Manual Gearbox Rebuilt

crankcase

By crankcase,
in Classifieds

 Share

Recommended Posts

crankcase Rookie

crankcase

Posted
Posted (edited)

R33 Rb25 Turbo manual Box, Rebuilt with New bearings and Syncros, Clips and Retainers, Torringtons and seals. Bellhousing has mods to Suit CA18 and RB. Comes with Shifter and Clutch Fork.
Will suit All RB VL And Skyline motors.

A good strong box. $1200

I am Negotiable.

Located Brisbane.

0434575801.

post-132527-0-27757700-1395045771_thumb.jpg

post-132527-0-05440700-1395045775_thumb.jpg

post-132527-0-03331900-1395045777_thumb.jpg

post-132527-0-44497400-1395045780_thumb.jpg

post-132527-0-60249200-1395045783_thumb.jpg

Edited by crankcase
drift_dingo Collaborator

drift_dingo

Posted
Posted

Hey,

What sorta mods does this need to suit a CA18? I mean would it need a different tailshaft...I've heard of fitting these to CA18 but not much info out there.

Thanks

~drft_dingo

crankcase Rookie

crankcase

Posted
  • Author
Posted

The bellhousing has been Clearanced for rear of CA Block By a mate. He was using this housing. The rear section i would assume is Attach the Yoke or even from centre bearing forward if its to short to match output spline. And use the Std tranny mount for CA. These assumptions are all based on how my mate had his setup.he used a navara box and this bellhousing.

 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Gareth87
      What should I do next to hold the head on

      By Gareth87 · Posted

      I can see between the water jacket and cyl 3 there wasn't a hard line of combustion gas. It certainly appears that the issue is coming from there. Yes, checked the tension. All at 100ft lbs where I set them 5 years ago. These blocks can crack but generally when they have been over bored. Mine is only 0.5mm oversize at 89.5mm. They break between cylinders around the 91mm mark. No sign of that with mine. My gut feeling is the head gasket lifted a while back when the studs stretched and i bandaided it by retorquing the studs. It's finally let go.
    • TurboTapin
      new 1.5 LSD issues/concerns

      By TurboTapin · Posted

      My Nismo 1.5 churps a bit on reverse turns when cold, but besides that feels like a stock diff.
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Yes, but, I paid cash and I'm pretty sure the receipt was in the bin 10 minutes after I got home Note to self, keep all receipts
    • MBS206
      NC MX5

      By MBS206 · Posted

      Bunnings would have just handed you your money back on that one!
    • The Bogan
      NC MX5

      By The Bogan · Posted

      So, version 4 intake is on its way I was looking at these a while ago but at around $200 or more it was a little pricey for something that might not work, but, I had it in my watch list, but, I got a message saying it was on special, and I had a code thingie to use, it eventually came in at $120 delivered, so BAM, BUY NOW.....LOL I'll need to have a look when it arrives but I feel it will "look" better than what I currently have, as it comes with a PCV fitting, so I will be able to get rid of the alloy pipe that goes to the throttle body with the PCV fitting  Well, that's what the voices in my head are telling me  Oh, and this happened today Yeap, it was a Trojan, and it was cheap, so I headed back to the hardware store and actually spent a little bit more on a heavy duty,  one that was actually recommended by a plumber mate, a Cyclone one with a fibreglass handle that is actually rated for clay The broken shovel will eventually be "modified" into a short handle shovel
×
×
  • Create New...