Jump to content
SAU Community

Recommended Posts

Thought I'd share this engine with you...

442ci General Motors based OHV V8

- no gaskets, just heat expanding O-rings

- extesive use of titanium.

- fluid dynamic crank to cut through the oil easier at speed

- turbos similar spec to what is found on Indy cars

Capable of 10000RPM (not bad for a 7.2L engine)

Early dyno run @ 25psi

1820Nm @ 7500RPM

2140hp @ 9000RPM

aiming for 2800hp with the boost set at 35psi

just the ticket for getting to work in my R32...

Link to comment
https://www.sau.com.au/forums/topic/44072-who-here-likes-nm/
Share on other sites

timbar32

it says 10,000RPM not 100,000RPM. Its not a turbine....

the type racing this will be used for involves a lot of runs per meet, so it has been engineered to produce this power consistantly with needing a rebuild every run.

Basically nothing in the entire engine is off the shelf. Even the cam is considerably thicker than in the engine its based on. The write up on this suggests rather extreme levels of engineering.

7.2L, 4 turbos & 10,000RPM would sound unbelievable on the track

Link to comment
https://www.sau.com.au/forums/topic/44072-who-here-likes-nm/#findComment-900725
Share on other sites

nah, the guy is fairly tight lipped about many of the exact details. there is just a repeated idea that 'it costs alot to run this sort of gear'. titanium valves, springs & retainers. billet ally/GRP rods, 55mm billet cam, magnesium/thin wall stainless turbos... its insane

i guess 'alot' would be quite an understatement

RB's are nice but i wanna turbo big block!

Link to comment
https://www.sau.com.au/forums/topic/44072-who-here-likes-nm/#findComment-900831
Share on other sites

iv heard about this car

that thing is street legal and competed in all the street legal drags around the states, for a little while but it was banned by all of them soon after haha just too farken quick lol :)

speaking bout big hp some guy accross east, managed to get a Marlin engine (spitfire from WWII) into a car, produces 3000hp. hehe crazy bastard!

Link to comment
https://www.sau.com.au/forums/topic/44072-who-here-likes-nm/#findComment-901001
Share on other sites

the 27L V12 Rolls Royce Merlin was in WW2 fighters such as the Spitfire, Mustang, etc. It was also used in tanks of the era.

Rod Hadfield of the Castlemaine Rod Shop fame has spent the best part of the last couple of decades engineering a Merlin into a '55 Chev body. Apparently it quite the animal. Its appeared on TV since its been finished but I still haven't seen it.

I was 15 last time I saw that car in the museum part of CRS & it was basically just a turret, chassis & engine.

Link to comment
https://www.sau.com.au/forums/topic/44072-who-here-likes-nm/#findComment-901067
Share on other sites

the 27L V12 Rolls Royce Merlin was in WW2 fighters such as the Spitfire, Mustang, etc. It was also used in tanks of the era.

Rod Hadfield of the Castlemaine Rod Shop fame has spent the best part of the last couple of decades engineering a Merlin into a '55 Chev body. Apparently it quite the animal. Its appeared on TV since its been finished but I still haven't seen it.

I was 15 last time I saw that car in the museum part of CRS & it was basically just a turret, chassis & engine.

It was on tv ages ago, can't remember what for but he was having a good talk about it . Was awesome.

Link to comment
https://www.sau.com.au/forums/topic/44072-who-here-likes-nm/#findComment-903737
Share on other sites

Guest INASNT
That's Mike Moran's car + motor there, he's a leading edge drag racer in the states who always seems to be driving customer's cars for them. Then he decided to build a car for himself, and look what he got :D

Yep that car has been in a special zoom magazine drag edition last year!

It was pulling low 6 second 1/4 times in that same shell last year

Link to comment
https://www.sau.com.au/forums/topic/44072-who-here-likes-nm/#findComment-904471
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hey Dave, welcome aboard! Good to see another soon-to-be Stagea owner here. The wagons are awesome — plenty of space, still got that Skyline DNA, and loads of potential if you’re into mods. Definitely post up pics when you get it, everyone here loves seeing new builds. What model/year are you looking at?
    • See if you can thermal epoxy a heatsink or two onto it?
    • The other problem was one of those "oh shit we are going to die moments". Basically the high spec Q50s have a full electric steering rack, and the povo ones had a regular hydraulic rack with an electric pump.  So couple of laps into session 5 as I came into turn 2 (big run off now, happily), the dash turned into a christmas tree and the steering became super heavy and I went well off. I assumed it was a tyre failure so limped to the pits, but everything was OK. But....the master warning light was still on so I checked the DTCs and saw – C13E6 “Heat Protection”. Yes, that bloody steering rack computer sitting where the oil cooler should be has its own sensors and error logic, and decided I was using the steering wheel too much. I really appreciated the helpful information in the manual (my bold) POSSIBLE CAUSE • Continuing the overloading steering (Sports driving in the circuit etc,) “DATA MONITOR” >> “C/M TEMPERATURE”. The rise of steering force motor internal temperature caused the protection function to operate. This is not a system malfunction. INSPECTION END So, basically the electric motor in the steering rack got to 150c, and it decided to shut down without warning for my safety. Didn't feel safe. Short term I'll see if I can duct some air to that motor (the engine bay is sealed pretty tight). Long term, depending on how often this happens, I'll look into swapping the povo spec electric/hydraulic rack in. While the rack should be fine the power supply to the pump will be a pain and might be best to deal with it when I add a PDM.
    • And finally, 2 problems I really need to sort.  Firstly as Matt said the auto trans is not happy as it gets hot - I couldn't log the temps but the gauge showed 90o. On the first day I took it out back in Feb, because the coolant was getting hot I never got to any auto trans issues; but on this day by late session 3 and then really clearly in 4 and 5 as it got hotter it just would not shift up. You can hear the issue really clearly at 12:55 and 16:20 on the vid. So the good news is, literally this week Ecutek finally released tuning for the jatco 7 speed. I'll have a chat to Racebox and see what they can do electrically to keep it cooler and to get the gears, if anything. That will likely take some R&D and can only really happen on track as it never gets even warm with road use. I've also picked up some eye wateringly expensive Redline D6 ATF to try, it had the highest viscosity I could find at 100o so we will see if that helps (just waiting for some oil pan gaskets so I can change it properly). If neither of those work I need to remove the coolant/trans interwarmer and the radiator cooler and go to an external cooler....somewhere.....(goodbye washer reservoir?), and if that fails give up on this mad idea and wait for Nissan to release the manual 400R
    • So, what else.... Power. I don't know what it is making because I haven't done a post tune dyno run yet; I will when I get a chance. It was 240rwkw dead stock. Conclusion from the day....it does not need a single kw more until I sort some other stuff. It comes on so hard that I could hear the twin N1 turbos on the R32 crying, and I just can't use what it has around a tight track with the current setup. Brakes. They are perfect. Hit them hard all day and they never felt like having an issue; you can see in the video we were making ground on much lighter cars on better tyres under brakes. They are standard (red sport) calipers, standard size discs in DBA5000 2 piece, Winmax pads and Motul RBF600 fluid, all from Matty at Racebrakes Sydney. Keeping in mind the car is more powerful than my R32 and weighs 1780, he clearly knows his shit. Suspension. This is one of the first areas I need to change. It has electronically controlled dampers from factory, but everything is just way too soft for track work even on the hardest setting (it is nice when hustling on country roads though). In particular it rolls into oversteer mid corner and pitches too much under hard braking so it becomes unstable eg in the turn 1 kink I need to brake early, turn through the kink then brake again so I don't pirouette like an AE86. I need to get some decent shocks with matched springs and sway bars ASAP, even if it is just a v1 setup until I work out a proper race/rally setup later. Tyres. I am running Yoko A052 in 235/45/18 all round, because that was what I could get in approximately the right height on wheels I had in the shed (Rays/Nismo 18x8 off the old Leaf actually!). As track tyres they are pretty poor; I note GTSBoy recently posted a porker comparo video including them where they were about the same as AD09.....that is nothing like a top line track tyre. I'll start getting that sorted but realistically I should get proper sized wheels first (likely 9.5 +38 front and 11 +55 at the rear, so a custom order, and I can't rotate them like the R32), then work out what the best tyre option is. BTW on that, Targa Tas had gone to road tyres instead of semi slicks now so that is a whole other world of choices to sort. Diff. This is the other thing that urgently needs to be addressed. It left massive 1s out of the fish hook all day, even when I was trying not too (you can also hear it reving on the video, and see the RPM rising too fast compared to speed in the data). It has an open diff that Infiniti optimistically called a B-LSD for "Brake Limited Slip Diff". It does good straight line standing start 11s but it is woeful on the track. Nismo seem to make a 2 way for it.
×
×
  • Create New...