Jump to content
SAU Community

Recommended Posts

Dear all,

I have done a search on the forums regarding poor fuel economy (R33 RB25DE Non-Turbo), however I am am at a bit of a loss on what I can do. After filling up on a full tank of Optimax last week, the needle was exactly at the 1/2 full mark at 200 km. Then the needle was at the 1/4 full mark at 240 km.

I drive daily across town (less than 10 km each way) from home to work and back, usually in peak hour traffic, lots of stop-start driving. Since the last fill, I have driven about 100 km on the freeway @ 100 km/h. I do accelerate hard usually - revving out to ~5K rpm..

Judging by the smell of the exhaust gases it smells like it’s running rich (I can smell the exhaust from the cabin) but there is no noticeable smoke at all. Plugs changed not that long ago, different AFM tried, put in a new battery 2 weeks ago (so ECU is reset). My car is stock apart from aftermarket exhaust and pod filter.

Usually I am getting approximately 350km off 50L of fuel.. (~15L/100km)

What are other RB25DE owners getting in the way of fuel economy? What else can I do?

cheers,

chicane

Link to comment
https://www.sau.com.au/forums/topic/44103-poor-fuel-economy-rb25de-help/
Share on other sites

You say that you were judging from 1/2 a tank to 1/4 of a tank.

It doesn't work that way.

If you fill the tank, you will get more K's between Full and half, than you will between half and empty.

When was the last time you changed your fuel filter?

Also take a look at the fuel you're using.

Optimax (in my opinion) isn't as good as some of the other available fuels, and you won't get the best economy on crappy fuel.

Guest RedLineGTR

Your Best bet is to look at possibly replacing your oxygen sensor :rant: i know one or two people who replaced thiers with a new one $120 dollars later (this was about a year or so ago) they got an extra 120km out of a tank this was in a turbo as well and an r32 gtst :rofl:

when i first got my skyline i had rather shittie fuel economy, but i later figured it was because i was doing alot of small drives, 15min each time. after i started driving alot more/ longer drives it got better n better. also before i bought my car it sat around for a few months n only got driven every so often so that may have been why aswell

1. never trust guages... they trick you

2. try some octane booster to clear out some build up on spark or fuel lines

3. check oxygen sensors...

4. check for fule lines just incase its not leaking some where under pressure

5. check your right foot... may have some build up of LEAD!!! :D

cheers

Joe

Thanks again for the replies people,

CroatianDlite: apparently U can use a Ford o2 sensor, not too sure on what the model is though.

I considered changing that but apparently the o2 sensor is only used by the car at idle? Can anyone confirm this?

buy a ford el oxygen sensor its the same part. its made by bosch. i got mine for $117 brand new. just say u need an 02 sensor for a ford el faclon at like repco and woila! problem solved

the o2 sensor gives feedback to the ecu so it can run lean and save fuel. thats its only purpose and lasts about 40,000ks before it dies.

when it (the o2 sensor) dies it cant tell the ecu to run lean and therefore the ecu just defaults to "rich" mode and waste's fuel. i did this on my series II r33 about a month ago and got a massive fuel economy increase. the ford el part worked fine.

I wasnt able to swap the sensor over as i didnt have the right tools. its a bitch to get to on the rb25 with normal shitty spanners. but if you do it yourself you need to cut the wires and match them yourself as the ford el sensor wont come with plug, just bare wires. theres two common wires (heater wires) and one power. so you cant really **** it up.

its not used by the car at idle. its used all the time. it plugs into your exhaust manifold and gives feedback to the ECU on exhaust gases and then the ecu can lean out the mixture when you arent on full throttle. the o2 sensor is only used when arent on full throttle. on full throttle the ecu just runs rich anyway

interesting, sounds like i need a new 02 sensor too then. when i first bought the car i could get 500k's out of it with some to spare. these days wen i'm up to the last quarter its only around 300ks.

for some reason, after i changed rims to 16" with wider tyres my economy went worst.

good idea to check ur plugs and replace em if necessary

looks like the new o2 sensor from FORD is doin the trick. if anyone has seen my other post, i talk about the engine "Stutterig" .. well it seems it has definately stopped that.. also the car seems to drive a lot smoother now! so far im impressed. but i havent done enough k's yet to tell u about fuel economy.... actually tomorrow night im going to rooty hill and back and that a 88 km round trip with traffic and freeway conditions. so ill get back to you on that...i usually blow 1/4 to half a tank.. depends on how fast i go... sometimes i can get home in 25 min... lol...

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...